background image

 

The PureLite XStream is only for use by trained, competent personnel

 

In the power-off state little or no respiratory protection is to be expected, and this 
is considered to be an abnormal situation

 

In the power-off state there will be a rapid buildup of carbon dioxide and depletion 
of oxygen may occur

 

Without the face seal fitted no respiratory protection is to be expected

 

At very high work rates and peak inhalation the pressure flow in the device may 
become negative

 

Ophthalmic spectacles may transmit impacts from high-speed particles, thus 
creating a hazard to the wearer

 

Never modify or alter this product, except as directed in the service tasks 
contained in these instructions

 

Materials which may come into contact with the wearer’s skin could cause 
allergic reactions to susceptible individuals

LEAVE THE CONTAMINATED AREA IMMEDIATELY IF 
ANY OF THE FOLLOWING CONDITIONS APPLY:

 

The buzzer sounds

 

Any part of the unit becomes damaged

 

Airflow into the unit decreases or stops

 

Breathing becomes difficult

 

Dizziness or other physical distress or irritation occurs

 

The user tastes or smells contaminants

Transportation

 

For transportation purposes use the carry bag provided and protect the 
unit from physical or chemical damage

3

Summary of Contents for PUREFLO PURELITE XSTREAM

























Reviews: