Genius RAINBOW 524 C, Manual For The Installer

Page: 25 / 56

RAINBOW 524 C- RAINBOW 724 C
ENGLISH
Instructions for use
Page
Carefully read the instructions before using the product.
Store these instructions for future reference.
Thank you for choosing our product. GENIUS is sure you will get the
performances you expect to satisfy your requirements.
All our products are the result of a many years’ experience in the
field of the automated systems, strengthened by being part of a
world leading group in this sector.
The automated systems of the RAINBOW family are electro-
mechanical barriers which have been designed and realised to
control vehicle accesses.
During design particular attention has been paid to the many
installation requirements. The result has been a product attentive
to installer ergonomy, the control unit is located on the upper
part of the automated system and can be rotated. Attention has
also been paid to the ease of installation: suitable facilities for the
photocells and the key-selector are present on the housing. Both
on the housing and on the rods you can install luminous strips,
replacing thus the traditional flashing lamp.
Thanks to the various types of rods available, these can be used in
very different types of accesses, from a minimum of 3 meters to a
maximum of 7 meters in case of single applications.
These automated systems consist of a steel structure with
powder paint enclosing the non-reversing electro-mechanical
gearmotor.
A handy release device, protected by customised key, enables you
to move the rod by hand in the event of a power cut.
Thanks to the use of 24V motors and of the encoder (standard
supplied), all automated systems of the RAINBOW family are able to
guarantee very high safety levels. If correctly installed, they realise
installations in compliance with current safety standards.
GENERAL SAFETY REGULATIONS
If correctly installed and used, the RAINBOW automated system
guarantees a high level of safety. Certain simple rules of behaviour
can also avoid accidental hitches:
Do not transit when the rod is moving. Transit is only allowed when
the beam is completely open.
Do not in any way stand under the rod.
Keep radio controls or any other pulse generators out of reach of
children, to prevent the automated system from being activated
involuntarily.
Do not allow children to play with the automated system.
Do not willingly impede the movement of the rod.
Prevent any branches or shrubs from interfering with the
movement of the rod.
Keep the signalling systems clearly visible and operating
efficiently.
Do not attempt to manually move the rod unless you have
released it.
In the event of malfunctions, cut power, release the rod to permit
access and wait for qualified personnel to do the necessary
work.
Once the system has been set in manual mode, before restoring
normal operation check that the system is not powered.
Do not make any modifications to the components of the
automated system.
Have the efficiency of the automated system checked every
six months.
Do not attempt any kind of repair or direct action whatsoever;
these operations must only be carried out by GENIUS qualified
personnel or by GENIUS service centres.
Make sure that the installing technician fills out the enclosed
maintenance register
MANUAL OPERATION
If a manual operation of the rod is necessary due to a fault of the
automated system or to a power cut, operate as follows:
Cut power to the system using the differential switch upstream
of the system.
Insert the key into the release device and turn it clockwise until it
stops, as shown in fig. 1 ref.
a
.
Turn the release device clockwise until it stops, fig. 1 ref.
b
.
Move the rod by hand, fig. 1 ref.
c
.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Fig. 1
RESTORING NORMAL OPERATION
To prevent an involuntary pulse from activating the automated
system, make sure the system is not powered up using
the differential switch, before restoring normal operation
mode.
Turn the release device counter-clockwise until it stops, Fig. 2
ref.
a
.
Turn the key counter-clockwise until it stops and then remove it, counter-clockwise until it stops and then remove it, clockwise until it stops and then remove it,
fig. 2 ref
b
.
Move the rod by hand until it stops, fig. 2 ref.
c
.
Power up the system.
Fig. 2
MAINTENANCE
To ensure a correct operation and a constant safety level over time
perform, every six months, a general check of the system paying
special attention to the safety devices. The booklet “Instructions
for use” contains a form for the registration of the maintenance
operations.
Every maintenance job must be performed by GENIUS qualified
personnel or by GENIUS service centres.
REPAIRS
The user must not attempt any repair or job and must only and
exclusively contact qualified GENIUS personnel or GENIUS service
centres.
•
•
•
•