Genius INTERMODO4 868, Manual

Page: 6 / 20

6
ENGLISH
3. MEMORY STORAGE OF RADIO CONTROLS
A maximum of 250 codes for channels 1-2 and 250
codes for channels 3-4 can be memory stored.
On the master radio control, simultaneously press and
hold down push-buttons P1 and P2.
The radio control LED begins to flash (for about 10
secs.).
Release both push-buttons.
Press, for 1 second, the push-button on the receiver
(Fig.1 ref. ) relating to the channel you wish to
associate with the radio control.
The relevant LED on the receiver (Fig. 1 ref. ) begins
to flash slowly for 5 secs.
Within these 5 secs., while the radio control LED is still
flashing, press and hold down the required push-but-
ton on the radio control (the radio control LED lights
up on steady beam).
The LED on the board (Fig.1 ref. ) lights up on steady
beam for 1 second and then goes OFF, indicating that
storage was executed.
Release the radio control push-button.
Quickly press twice in succession the memory stored
radio control push-button.
The board will send a command to the output
associated with the channel.
To add other radio controls, transfer the code of the
memory-stored push-button of the radio control to
the relevant push-button of the radio controls to be
added, observing the following procedure:
On the memory stored radio control, simultaneously
press and hold down push-buttons P1 and P2.
The radio control LED begins to flash.
Release both push-buttons.
Press the memory stored push-button and hold it
down (the radio control LED lights up on steady
beam).
Bring the radio controls near, press and hold down
the push-button of the radio control to be ad-
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
a–
b–
c–
d–
e–
ded, releasing it only after the double flash of
the radio control LED, which indicates learning
was executed.
Quickly press twice the push-button of the new
memory stored radio control.
The board will send a command to the output
associated with the channel.
4. DELETION OF ALL RADIO CONTROLS
ASSOCIATED WITH CHANNELS 1-2 OR 3-4
This operation is NOT reversible and, if the radio con-
trols associated with channels 3-4 are deleted,
it also entails the deletion of activation timer of
output 4.
To delete ALL the radio control codes associated
with channels 1-2 or 3-4, hold down the rele-
vant push-button (Fig.1 ref. ) for 10 seconds.
(e.g. TO DELETE ALL RADIO CONTROLS ASSOCIATED
WITH CHANNELS 1-2, PRESS SW1 OR SW2).
The LED (Fig.1 ref. ) relating to the pressed push-
button flashes for the first 5 secs., and then flashes
more quickly for the next 5 secs.
The LED lights up on steady beam for 2 secs. and
then goes OFF.
Release the pressed push-button when the relevant
LED lights up on a steady beam.
f–
1.
2.
3.
4.
5. FUNCTION LOGIC
You can command the receiver channels from different radio controls. (E.g.: radio control 1 commands channel
1, radio control 2 commands channel 2, etc..)
PULSE FROM RADIO CONTROL PULSE FROM RADIO CONTROL
CHANNEL 1
CHANNEL 2
dip switch 1=OFF
CHANNEL 2
dip switch 1=ON
CHANNEL 3 CHANNEL 4
OUTPUT 1 PULSE / / / /
OUTPUT 2 / PULSE
CONTACT CLOSED
UNTIL NEXT PULSE
FROM REMOTE
CONTROL
/ /
OUTPUT 3 / / / PULSE /
OUTPUT 4 / / / /
CONTACT CLOSED
UNTIL END OF PRO-
GRAMMED TIME
CHANNEL 1
CHANNEL 2
dip switch 1=OFF
CHANNEL 2
dip switch 1=ON
CHANNEL 3 CHANNEL 4
OUTPUT 1 PULSE / / / /
OUTPUT 2 / PULSE
CONTACT CLOSED
UNTIL NEXT PULSE
FROM REMOTE
CONTROL
/ /
OUTPUT 3 / / / PULSE /
OUTPUT 4 / / / /
CONTACT CLOSED
UNTIL END OF PRO-
GRAMMED TIME