background image

4

©2011 The Genie Company

 

 

 

9/2011

SET

PROGRAM

Open 

Travel

ROUND LED

Indicator

Facing

Garage Door

Close

Travel

Button

 

OVERVIEW OF POWERHEAD CONTROLS

This section describes the simple programming 
functions.  Use this page to familiarize yourself with the 
buttons and LED indicators used to program the opener.

NOTE: 

These   and   buttons are for programming use 

only.  Do 

NOT

 use these buttons to operate the opener. 

There are three programming buttons and two lights 
(LEDs) on the powerhead.
Each of the buttons are used to enter and complete 
the setup programming.  The LEDs indicate status or a 
function change by illuminating ON, OFF, or ON 

flashing

 

in one of three different colors: BLUE, RED, or PURPLE.

PROGRAM

SET

   Enters into and selects programming menus.  

 

  

 

 

 

 

Programming Overview

There are four Powerhead program menus:

Remote Program (Default menu)
Limits Program

Speed Program**

Force Program*

*

Force settings are set at the factory and do not normally 
require operator programming but can require minor 

**

  Speed settings are set at the factory and are self-
adjusting when needed. Speed Settings do not normally 
require manually initiated changes. 

1

Located on bottom of Powerhead.

Begin here ONLY AFTER 

 

d

n

a

 

y

l

b

m

e

s

s

a

 

g

n

i

t

e

l

p

m

o

c

installation of the opener.
Review the Assembly & 
Installation Poster to

ensure all steps have
been performed.

There are no assembly or installation 
steps included in this manual. Contact 
your Genie® Professional Dealer for an 
installation poster, if needed, or call 
1-800 35-GENIE. You may also visit 
www.geniecompany.com to download 
a pdf. file.

Before you begin Programming, 
check to make sure there are no 
objects in the garage 
door opening.

INFRARED PROTECTION FUNCTION

1.

  The Safe-T-Beam® has no effect on the door 

during an opening cycle.

2.

  If the Safe-T-Beam® detects an obstruction 

when trying to close the door, it will not allow 
the door to move.

3.

  When the garage door is closing, if Safe-T-Beam®

 is interrupted by person or obstacle, the garage 

door will stop its downward travel and reverse 

automatically to its fully opened position.

4.

   If the Safe-T-Beam® System fails, loses power, or 

is installed improperly, press and hold the wall 

console "open/close" button until the door

 reaches its fully closed position.  If you release the

"open/close" button on the wall console during
the closing movement the door will reverse 

automatically to its fully opened position.

adjustment under certain conditions. 
See Troubleshooting.

LONG LED

Indicator

Multi-function; move door during programming 
& advance through menus

Both LEDs can be Red, Blue, Purple or off, depending on the 
programming step you are performing. 

ADJUSTMENT OF FORCE & SPEED SETTINGS IS ON PAGE 10
IN THE MAINTENANCE & TROUBLESHOOTING SECTION. 

Summary of Contents for IntelliG 1000















Reviews: