background image

 

 

©2011 The Genie Company

9/2011

5

WARNING

s

 Make sure doorway is in view and clear of obstacles and 

people to avoid injury or damage to property.

s

 DO NOT operate this unit from wall console before LIMITS 

and FORCE are set.  Severe damage to the opener can occur. 

s

 The bullet MUST be engaged to carriage BEFORE setting  

limits.  See Installation Poster (if provided) or call 
Customer Service at 800-35-GENIE or visit 
www.geniecompany.com.

NOTE: If bullet has NOT been engaged to 
the carriage, do so no .

PROGR

2

Please note that there is a 

30 second timeout

 between 

 each programming step.

If you see 

two flashing RED LEDs

, you have initiated 

a timeout.
In the ev

w  See page 9.

CONTACT REVERSE TEST

 

The Force and Limit settings MUST be COMPLETED 

before performing Contact Reverse Test.

1.

 

Test.

 

Place a 2" x 4" 
board (laid flat) 
under center of 
door opening.

 

2. Adjustment, if needed.

s

 If the door 

stops before it contacts the board

 

WARNING

 

A moving door can cause serious injury or death.

1.

   Keep people clear of opening while door is moving.

2. 

 Do 

NOT

 allow children to play with opener, including 

wall console, remote, or wireless keypad.

3. 

  During programming, door opener could begin to run, 

so stay away from moving door and its parts.

 

Once the Contact Revese Test is complete, 
continue with programming Remotes.

or it 

does not reverse, 

it may be due to an improperly set 

down limit. Repeat TRAVEL LIMITS program and 

Test again.

Repeat as needed until door passes test. For further help 
refer to Maintenance &Troubleshooting, page 13.
   

ent of a timeout you must restart at beginning. 

Press & hold 
2 seconds or until 
LEDs react. Release.

Press & hold 
2 seconds or until 
LEDs react. Release.

Long LED turns Blue, 
Round LED OFF.

Then Long LED OFF
Round LED Flashing.

Long LED turns Blue, then flashes.

Press & hold
until door  is fully 
open. Then release.

Press & 
Release.

DOOR LIMITS ARE SET

SET FORCE NEXT

PROGRAM

SET

 

FLASHING

DOOR FULLY OPEN

DOOR FULLY CLOSED

OFF

O

RED

RED

FF

Press & 
Release.

PROGRAM

SET

 

Press & 
Release the
Open/Close 
button.

DOOR CLOSES.

s

  When door contacts board, 

   it must stop and reverse direction 
   (within 2 seconds) to the fully 
   open position.

OFF

OFF

AMMING LIMITS 

TRAVEL LIMITS

UP LIMIT

DOWN LIMIT

Door fully closes.

Door fully opens.

FORCE CONTROL

Press & 
Release
Open/Close 
button.

ACTION    

           INDICATION/RESULT

ACTION    

           INDICATION/RESULT

Press & 
Release
Open/Close 
button.

ON WALL CONSOLE

 

Press & 
Release the
Open/Close 
button.

FORCE CONTROL IS SET

1

2

1

2

1

3

4

5

6

2

3

DOOR OPENS.

ACTION    

                         LED INDICATION/RESULT

OFF

OFF

ON

BLUE 

BOTH FLASH BLUE

FLASHING

Press & hold
until door  is fully 
closed. Then release.

B

During the initial setting 
of the limits- the LEDs will 
turn to RED—NOT OFF

oth BLUE then LEDs Off confirms limit set.

OFF

OFF

BOTH FLASH BLUE

Both BLUE then LEDs Off confirms limit set.

Summary of Contents for IntelliG 1000















Reviews: