GeneralTouch SAW Installation Manual Download

Page: 2 / 22

GENERALTOUCH TECHNOLOGY CO., LTD

Issued by: Customer Service Department 2

22 Issued Date: 2013.10.14

发行部门：客户服务部

发行时间：

2013.10.14

Table of Contents

Introduction for GeneralTouch SAW Touch Screen

吉锐声波触摸屏介绍

........................................................ 3

Installation Key Points for GeneralTouch SAW Touch Screen

吉锐声波触摸屏安装要点

.............................. 5

SOP for GeneralTouch SAW Touch Screen Assembly

吉锐声波触摸屏安装作业指导书

.............................. 7

Disassemble the front frame and the back cover of the monitor

拆下显示器前框和后盖

........................... 7

Assemble the touch screen

安装触摸屏

............................................................................................................. 7

Assemble the controller

安装控制器

.................................................................................................................. 10

Cable routing and the ending

布线及完成组装

................................................................................................ 11

Notes

注意事项

.................................................................................................................................................... 15

Protect the transducers and the touch screen cable

保护换能器和屏线

................................................. 15

The dust-proof solution

防尘方案

.................................................................................................................. 18

Appendix

附录

.......................................................................................................................................................... 21

Touch Screen Care and Cleaning

触摸屏维护和清洁

.................................................................................... 21

Touch Screen Transportation

触摸屏运输

........................................................................................................ 21

Contact Information

联系方式

............................................................................................................................ 22

Summary of Contents for SAW























Search results

Summary of Contents for SAW

Reviews:

Related manuals for SAW

Brands by name

Popular brands

GeneralTouch SAW, Installation Manual

Search results

Summary of Contents for SAW

Reviews:

Related manuals for SAW

Brands by name

Popular brands