![background image](http://html.mh-extra.com/html/general-pipe-cleaners/mini-rooter-xp/mini-rooter-xp_operating-instructions-manual_2210605008.webp)
Mini-Rooter XP
®
8
MAINTENANCE
To keep your machine operating smoothly, it is essential that all bear-
ings and distributor tube bushings be lubricated. Oiling moving parts is
particularly important where machine comes in contact with sand, grit
and other abrasive material.
CABLE MAINTENENCE
To get maximum service from your cables, be
sure that they are clean and well oiled. This not
only provides running lubrication but greatly ex-
tends the life of the cables as well. Some users
periodically pour oil directly into the drum. Then,
as the drum turns, the cables get complete lubri-
cation. Our SNAKE OIL is ideally suited for this
purpose, since it not only lubricates the cables, it
deodorizes them as well.
FEED MAINTENANCE
Keep feed free of excessive soil and grit. It is recommended that the
feed be flushed with fresh water followed by a light oiling of the mov-
ing parts. No disassembly is normally required. Failure to feed can
usually be traced to the following possibilities:
DIRT ACCUMULATION
Over time, dirt can harden enough to stop roller rotation. Flushing with
water followed by liberal oiling can usually restore function. If disas-
sembly is required, proceed as follows:
1. Remove the feed tension knob, springs and spring plunger. Note
the positioning of these parts to ease re-assembly. The top roller
can now be removed.
2. Remove the snap rings and thrust washers from the bottom
housing cylinders. The bottom rollers can now be removed.
3. Re-assembly is done in reverse order.
TANGLED CABLE
If a cable loops over itself in the drum, it will not feed properly. Re-
move and reload the cable to restore function. If the cable kinks, it is
evidence of abuse and results from the use of too much pressure or
use of the wrong size cable for the line. Do not force the cable
—
let
the cutter do the work.
DAMAGED ROLLER
Excessive use may wear a roller to the point of failure. It is recom-
mended that all three rollers be replaced at the same time (Cat # PO-
MR-703). The replacement roller is an assembly consisting of one
Feed Roller, two Feed Roller Bearings, and two Bearing Spacers.
Note: The Bearing Spacers must be installed between the Carrier
and each Feed Roller Bearing (as illustrated below) in order to
ensure proper operation and to obtain maximum Feed Roller life.
To Replace the Feed Roller Assembly:
1. Remove the Feed Roller Assembly by unscrewing and removing
the Feed Roller Axle.
2. For convenience, the components are assembled and wired
together at the factory. Before attempting to install the assembly,
hold the assembly together and remove the wire.
3. While still holding the Feed Roller Assembly together, insert it
into the slot opening of the Carrier.
4. In order to help align the Spacers and Bearings, insert a pencil
point or similar object through the
un-threaded
end of the Axle
hole in the Carrier. After removing the pencil point, continue to
maintain the alignment of the components.
5. The Feed Roller Axle should then be inserted through the same
un-threaded Axle hole and should continue to be guided through
the Spacers and Bearings to the threaded Axle hole on the other
side of the Carrier.
6.
Securely tighten the Axle to the Carrier with a 3/16” allen wrench.
DISCONNECT MACHINE FROM POWER SOURCE
BEFORE PERFORMING MAINTENANCE!
2. Slide the back end of the cable (opposite to the end with basin
head) through spout and into the drum. The cable will be easier
to install if you bend the last inch of cable at a 45-degree angle.
3. When working through difficult stoppages or tight bends, tighten
the chuck to provide more torque and to prevent the cable from
tangling in the drum.
4. Clean and lubricate chuck regularly to prevent corrosion.
Summary of Contents for Mini-Rooter XP
Page 10: ...Mini Rooter XP 10 ...