Generac Power Systems RTSJ200A3 Owner'S Manual Download Page 2

Safety Rules .................................................Inside Front Cover
General Information ................................................................. 2

1.1 Introduction 

................................................................................ 2

1.2 Equipment 

Description 

................................................................ 2

 

1.2.1  Transfer Switch Mechanism .............................................. 2

 

1.2.2  Utility Service Disconnect Circuit Breaker .......................... 2

 

1.2.3  Load Shed Controller ........................................................ 3

1.3  Transfer Switch Data Decal ......................................................... 3
1.4  Transfer Switch Enclosure ........................................................... 3
1.5  Safe Use Of Transfer Switch........................................................ 4

Installation ............................................................................... 4

2.1  Introduction to Installation ........................................................... 4
2.2 Unpacking 

.................................................................................. 4

2.3 Mounting 

.................................................................................... 4

2.4  Connecting Power Source and Load Lines .................................. 4
2.5 Neutral 

Connections 

.................................................................... 5

2.6  Connecting Control Wires ........................................................... 5

Operation ................................................................................. 5

3.1  Functional Tests & Adjustments .................................................. 5
3.2 Manual 

Operation 

........................................................................ 5

 

3.2.1  ATS Manual Operation ...................................................... 5

 

3.2.2  LSS Manual Operation ...................................................... 6

 

3.2.3  Close to Utility Source Side ............................................... 6

 

3.2.4  Close to Generator Source Side ........................................ 6

 

3.2.5  Return to Utility Source Side ............................................. 6

3.3 Voltage 

Checks 

........................................................................... 7

3.4  Generator Tests Under Load ........................................................ 8
 

3.4.1  ATS & Critical Loads ......................................................... 8

 

3.4.2  Auto Operation and Load Shed Functional Test .................. 8

Notes ....................................................................................... 9
Installation Diagram .............................................................. 12
Interconnection Diagram ....................................................... 13

SAFETY RULES

 

 SAVE THESE INSTRUCTIONS - This manual 

contains important instructions that should 

be followed during installation and mainte-

nance of the generator and batteries.

 

 SAVE THESE INSTRUCTIONS!  Read the fol-

lowing information carefully before attempt-

ing to install, operate or service this equip-

ment. Also read the instructions and infor-

mation on tags, decals, and labels that may 

be affixed to the transfer switch. Replace any 

decal or label that is no longer legible.

 

 DANGER!  Connection of a generator to an 

electrical system normally supplied by an 

electric utility shall be by means of suitable 

transfer equipment so as to isolate the elec-

tric system from utility distribution system 

when the generator is operating (Article 701 

Legally Required Standby Systems or Article 

702 Optional Standby Systems, as appli-

cable). Failure to isolate electric system by 

these means may result in damage to gen-

erator and may result in injury or death to 

utility workers due to backfeed of electrical 

energy.

The manufacturer cannot anticipate every possible circumstance 

that might involve a hazard. The warnings in this manual, and on 

tags and decals affixed to the unit are, therefore, not all-inclusive. If 

using a procedure, work method or operating technique the manu-

facturer does not specifically recommend, ensure that it is safe for 

others. Also make sure the procedure, work method or operating 

technique chosen does not render the transfer switch unsafe.

Table of Contents

WARNING!

California Proposition 65

Engine exhaust and some of its constituents are known to the state of California to cause cancer, 

birth defects, and other reproductive harm.

WARNING!

California Proposition 65

This product contains or emits chemicals known to the state of California to cause cancer,

birth defects, and other reproductive harm.

Summary of Contents for RTSJ200A3

















Reviews: