Generac Power Systems PWRmanager Owner'S Manual Download Page 6

Safety Rules & General Information

2

Owner’s Manual for Generac PWRmanager 12 Relay Load Controller

General Hazards

Only competent, qualified personnel should install,

operate, and service this equipment. Strictly com

-

ply to local, state, and national electrical and build

-

ing codes. When using this equipment, comply with

regulations  established  by  the  National  Electrical

Code  (NEC),  CSA  Standard;  the  Occupational

Safety  and  Health Administration  (OSHA),  or  the

local agency for workplace health and safety.

Protection against lightning  surges  in  accordance

with local electric codes is the responsibility of the

installer.

NOTE: 

Lightning damage is not covered by warranty.

Never  work  on this equipment while physically or

mentally fatigued.

Any  voltage  measurements  should  be  performed

with a meter that meets UL3111 safety standards,

and meets or exceeds overvoltage class CAT III.

Electrical Hazards

(000188)

DANGER

Electrocution. Do not wear jewelry while 
working on this equipment. Doing so will 
result in death or serious injury.

WARNING

(000747)

Risk of Injury. Do not operate or service this 
equipment if not fully alert. Fatigue can impair the 
ability to operate or service this equipment and could 
result in death or serious injury.

(000209b)

WARNING

Loss of life. This product is not intended to 
be used in a critical life support application. 
Failure to adhere to this warning could result 
in death or serious injury.

(000155a)

WARNING

Electric shock. Only a trained and licensed electrician 
should perform wiring and connections to unit. Failure to 
follow proper installation requirements could result in death, 
serious injury, and equipment or property damage.

(000182a)

WARNING

Equipment damage. Only qualified service personnel may 
install, operate, and maintain this equipment. Failure to 
follow proper installation requirements could result in death, 
serious injury, and equipment or property damage.

(000104)

DANGER

Electrocution. Water contact with a power 
source, if not avoided, will result in death 
or serious injury.

(000145)

DANGER

Electrocution. In the event of electrical accident, 
immediately shut power OFF. Use non-conductive 
implements to free victim from live conductor. Apply 
first aid and get medical help. Failure to do so will 
result in death or serious injury.

(000152)

DANGER

Electrocution. Verify electrical system is
properly grounded before applying power.
Failure to do so will result in death or serious
injury.

WARNING

(000745a)

Electrocution. PWRmanager Touch-Safe cover should be removed 
by a qualified technician only. Removing the Touch-Safe cover 
could result in death, serious injury, or equipment or property 
damage.

Summary of Contents for PWRmanager

























Reviews: