background image

Operation

10

Owner’s Manual for MWT500 Water Trailer

Reservoir as Fill Source

1.

Se

Figure 2-3

. Remove tank cover. Open valve 1. 

Close valves 2, 3, and 4. Close gravity drain bibb.

2.

On the lower manifold, open the cam-lock fitting 
and remove the end-plug. Attach cam-lock end of 2 
in. rigid fill-hose to the manifold.

3.

Attach basket strainer to threaded end of 2 in. rigid 
fill-hose. 

4.

Place hose in water.

5.

Prime the pump: 

a.

Remove plug of access hole. 

b.

Pour water into access hole, filling the pump 

housing. 

c.

Start the engine. 

The tank begins to fill through the supply pipe.

6.

Fill tank to desired level, then shut off engine.

7.

Close valve 1. Remove 2 in. rigid fill-hose from 
lower manifold and allow hose to drain. Place hose 
in storage bin.

8.

Close lower manifold end-plug. Secure cam-lock 
fitting on end-plug. Close tank cover.

Discharging Water from Tank

Using Rear Spray Bar

1.

Position trailer for proper use of rear spray nozzles.

2.

See 

Figure 2-3

. Open valve 4. Close valves 1, 2, 

and 3. Close gravity drain bibb.

3.

Start engine.

4.

Open valve 2. Water begins discharging through 
nozzles of rear spray bar.

NOTE: 

The spray pattern is adjustable. See 

Adjusting 

Rear Spray Bar

.

5.

When tank is empty, shut off engine and close 
valves 2 and 4.

Using 2-Inch Flexible Spray Hose

1.

See 

Figure 2-3

Close valves 1, 2, 3, and 4. Close 

gravity drain bibb.

2.

Remove one upper manifold end-plug. Attach cam-
lock fitting of 2 in. flexible spray hose to manifold 
and secure the cam-lock fitting. Eliminate bends 
and kinks in hose. Close nozzle of hose.

3.

Open valve 4.

4.

Start engine. 
The hose pressurizes and is ready for use. 

NOTE: 

Twist hose to turn on and off, and to adjust spray 

pattern.

5.

When tank is empty, shut off engine. Remove hose 
from upper manifold and allow hose to drain. 
Return hose to storage bin.

6.

Secure end-plug to upper manifold (B) and secure 
cam-lock fitting.

7.

Close valve 4.

(000385)

Personal Injury. Do not reach into pump 
housing with engine running. Doing so will 
result in death or serious injury.

DANGER

DANGER

Not for human consumption. Water in tank is not 
potable. Using tank water for human consumption 
will result in death or serious injury.

(000361)

(000117b)

Personal injury. Rick of fluid injection. 
Do not aim spray gun at people, animals, 
electrical devices, or fragile items. Keep out
of reach of children. Failure to do so
may cause death or serious injury.

WARNING

WARNING

Equipment damage. Do not allow pump to run dry. 
Doing so will cause the pump to overheat and could 
cause equipment damage.

(000380)

WARNING

Equipment damage. Running pump with closed 
valves will cause pump to overheat and could result 
in equipment damage.

(000381)

WARNING

Personal injury and equipment damage. Do not drive 
over pressurized hoses. Doing so could cause hose 
rupture and result in personal injury and equipment 
damage.

(000382)

Discount-Equipment.com

Summary of Contents for Magnum MWT500
























Reviews: