Gemtek Systems R921212G User Manual Download Page 20

Page: 20 / 92

Launch the Setup Wizard

Setup Wizard Screens

Introduction

Setup Wizard is an easy-to-use program included on your CD. It provides simplified

configuration procedures for establishing Internet connectivity on the Router. The Setup

Wizard first extracts the connection settings from your active ISP connection on your computer

with a cable/DSL modem. It then displays a series of graphical illustrations on how to connect

the router to the network. Finally it applies the extracted settings on your router and validates

its installation. If the installation cannot be completed successfully, the Setup Wizard will

display troubleshooting instructions to guide you through the installation process.

In addition, the Setup Wizard also provides links to the user's guide on the CD and the Dell

support website.

Launch the Setup Wizard

To run the Setup Wizard, perform the following steps:

Insert the CD

Summary of Contents for R921212G





























































































Search results

Summary of Contents for R921212G

Reviews:

Related manuals for R921212G

Brands by name

Popular brands

Gemtek Systems R921212G, User Manual

Search results

Summary of Contents for R921212G

Reviews:

Related manuals for R921212G

Brands by name

Popular brands