Gemtek Systems R921212G User Manual Download Page 48

Page: 48 / 92

Allow Remote User to Configure the Device

This option allows you to configure the device from a remote location via the network.

1. Click to select

Allow remote user to configure the device

2. Enter the IP address of the remote administration host in the required field.

3. Enter the HTTP port number that will be used on the router in the

HTTP port number

field.

4. Click

the

Apply

button to save the settings, or click the

Restore

button to restore to its

previous settings.

Allow Remote User to Ping the Device

This option allows you to configure the WAN ping capability. The default setting is

disabled

The router will not answer ping requests, so your WAN port is invisible to port scanners, which

can make your network safer.

Summary of Contents for R921212G





























































































Search results

Summary of Contents for R921212G

Reviews:

Related manuals for R921212G

Brands by name

Popular brands

Gemtek Systems R921212G, User Manual

Search results

Summary of Contents for R921212G

Reviews:

Related manuals for R921212G

Brands by name

Popular brands