manualshive.com logo in svg

Gemalto MagIC3 X-series, Maintenance Manual, Page: 13 / 37

Share
Download
Gemalto MagIC3 X-series Maintenance Manual Download Page 13

E-Payment

  

            

MagIC

3

 X-series  -  MAINTENANCE MANUAL 

Chapter 1 : 

DESCRIPTION 

Ref: 22000-00-MAN-I-09004 

 

 

June 2009 

 

 

 

                Ch.1 - 13/37 

Copyright Gemalto – 2008 

No disclosure to a third party without prior written consent of Gemalto

 

2.2.11 Modem 

The modem function is built around Silicon-Labs devices, the two-chip modem DSP Si2415 
and the DAA Si3018. This solution includes a DSP data pump, modem ctrl, on-chip RAM 
and ROM, codec, and DAA. 

The main characteristics of the modem are : 

•

  Compatibility with Bell 103, 212A, V21, V22, V22bis, V32, V32bis 

•

  Connect rate from 300 bps to 14.4 kbps 

•

  Fast connect (V22/V22bis fast handshake to connect to NAC hypercom for instance) 

•

  Accept standard AT commands 

•

 International 

PSTN 

•

  Programmable (to meet worldwide PSTN regulations with a single design) 

•

  Parallel phone detection 

•

 Incoming 

call 

 

2.2.12 Ethernet 

The AT91RM9200 includes an Ethernet Macrocell that provides a full-function 10/100 Base-
T Ethernet MAC (Media Access Controller) compliant with IEEE 802.3 standards. 
 

2.2.13 USB 

•

  2x USB 2.0 master, full speed and low speed (1.5 and 12 Mbps), 500 mA shared 

between the 2 lines. 

•

  1x USB 2.0 device, full-speed compliance, 12 Mbps. 

 

2.2.14 RS232 

•

  Simple RS232 (Tx-Rx-Gnd + DTR). Communication can go up to 115.2 Kbps.  

•

  Simple RS232 (Tx-Rx-Gnd + Vin power supply). Dedicated to the Pinpad. 

 

Summary of Contents for MagIC3 X-series






































Reviews:

No comments