Gemalto Cinterion ELS31T-J Hardware Interface Description Download Page 20

Page: 20 / 102

Cinterion

LTE Terminals Hardware Interface Description

2 Product Concept



ELSxT_HID_v04

2018-09-04

Confidential / Preliminary

Page 20 of 102

Product Concept

2.1

Key Features at a Glance

Feature

Implementation

General

Incorporates Cinterion

LTE module

The LTE module handles all signal and data processing within the LTE Ter-

minals. Internal software runs the application interface and the complete

GSM/UMTS/LTE protocol stack.

Frequency bands

ELS61T-US:

UMTS/HSPA+: Triple band, 850 (BdV) / AWS (BdIV) / 1900MHz (BdII)

LTE: Quad band, 700 (Bd12) / 850 (Bd5) / AWS (Bd4) / 1900MHz (Bd2)

ELS61T-AUS:

UMTS/HSPA+: Triple band, 850 (BdV) / 900 (BdVIII) / 2100 MHz (BdI)

LTE: Quad band, 700 (Bd28) / 900 (Bd8) / 850 (Bd5) / 1800MHz (Bd3)

ELS61T-E

GSM/GPRS/EDGE: Dual band 900/1800MHz

LTE: Penta band, 700 (Bd28) / 800 (Bd20) / 900 (Bd8) / 1800 (Bd3) /

2100 MHz (Bd1)

ELS61T-E2

GSM/GPRS/EDGE: Dual band 900/1800MHz

UMTS/HSPA+: Dual band, 900 (BdVIII) / 2100MHz (BdI)

LTE: Penta band, 700 (Bd28) / 800 (Bd20) / 900 (Bd8) / 1800 (Bd3) /

2100 MHz (Bd1)

ELS31T-V:

LTE: dualband, AWS (Bd4), 700MHz (Bd13)

ELS31T-J:

LTE: Triband, 2100 (Bd1), 850 MHz (Bd18, Bd19)

GSM class

Small MS

Summary of Contents for Cinterion ELS31T-J







































































































Search results

Summary of Contents for Cinterion ELS31T-J

Reviews:

Gemalto Cinterion ELS31T-J, Hardware Interface Description, Page: 20 / 102

Search results

Summary of Contents for Cinterion ELS31T-J

Reviews: