manualshive.com logo in svg

Gemalto Cinterion ELS31T-J, Hardware Interface Description, Page: 10 / 102

Share
Download
Gemalto Cinterion ELS31T-J Hardware Interface Description Download Page 10

Cinterion

®

 LTE Terminals Hardware Interface Description

1 Introduction

19

ELSxT_HID_v04

2018-09-04

Confidential / Preliminary

Page 10 of 102

1

Introduction

This document

1

 describes the hardware of the Cinterion

®

 LTE Terminals. The LTE Terminals 

come in five variants depending on the included Cinterion

®

 module:

•

ELS61T-US 

for use in North America and countries with similar radio bands.

•

ELS61T-AUS 

for use in Australia.

•

ELS61T-E 

for use in Europe and countries with similar radio bands.

•

ELS61T-E2 

for use in Europe and countries with similar radio bands, supporting voice

•

ELS31T-V 

for use in North America in Verizon Wireless Network.

•

ELS31T-J 

for use in Japan.

All LTE Terminals implements an Ethernet interface with a RJ-45 8-pin connector and also a 
V.24 / V.28 RS-232 interface with a D-sub 9-pole female socket as well as a 6-pole Western 
jack as plug-in power supply connector.

Wherever necessary and appropriate this document distinguishes between these five variants.

Table 1

 gives a short overview of the available interfaces for the different LTE Terminals.

The scope of this document includes interface specifications, electrical as well as mechanical 
characteristics of the LTE Terminals. It specifies standards pertaining to wireless applications 

1.  The document is effective only if listed in the appropriate Release Notes as part of the technical docu-

mentation delivered with your Gemalto M2M product.

Table 1:  

Cinterion

®

 LTE Terminals overview

Module/Interface

ELS61T-
US 

ELS61T-
AUS 

ELS61T-E 

ELS61T-E2

ELS31T-V  ELS31T-J 

Cinterion

®

 m

odule

ELS61-US

ELS61-

AUS

ELS61-E2 ELS61-E 

R2 ELS31-V

ELS31-J

LTE

Cat. 1

Cat. 1

Cat. 1

Cat. 1

Cat. 1

Cat. 1

UMTS/HSPA+

HSDPA 

Cat.8 / 

HSUPA 

Cat.6

HSDPA 

Cat.8 / 

HSUPA 

Cat.6

-

HSDPA 

Cat.8 / 

HSUPA 

Cat.6

-

-

GMS/GPRS/

EDGE

-

-

GPRS:

Multislot 

Class 12

EGPRS:

Multislot 

Class 12

GPRS:

Multislot 

Class 12

EGPRS:

Multislot 

Class 12

-

-

RS232 / supports 

autobauding

/

/

/

/

/-

/-

GPIO

ASC1

I2C/SPI

/

/

/

/

/-

/-

DAI

-

-

-

-

-

Java

-

-

Summary of Contents for Cinterion ELS31T-J







































































































Reviews:

No comments