manualshive.com logo in svg

Gema MultiStar CG10, Operating Instructions And Spare Parts List

Share
Download
Gema MultiStar CG10 Operating Instructions And Spare Parts List Download Page 54

 

Rev. 00  08/17

 

54  

  Fault clearance 

MultiStar CG10 

Code 

Description 

Criteria 

Remedy 

H67 

Supplementary air 
position lost 

Lost steps, limit switch defective, 
throttle motor defective 

Contact a Gema service 
center 

H68 

Electrode rinsing air 
position lost 

Lost steps, limit switch defective, 
throttle motor defective 

Contact a Gema service 
center 

Gun Controller 

190 

Communication error 
MU 

Disruption or damage to the 
connection between the 
additional panel print board and 
Gun Controller, invalid command 
parameter, command is not 
supported. etc. 

Contact a Gema service 
center 

290 

Communication error 
AU 

194 

Firmware Update 
necessary MU 

The Gun Controller firmware is 
not up-to-date. 

Update, contact Gema 
service 

294 

Firmware Update 
necessary AU 

192 

Gun Controller MU 
does not react 

No connection can be made with 
the Gun Controller. 
Reason: Additional device 
connected, but not activated. 

Contact a Gema service 
center 

292 

Gun Controller AU 
does not react 

 

 

Help codes list 

The last appeared eight errors are stored in a list by the software. If an 
error appears, which is already in the list, he will not be listed again. 

 

Appearance of errors 

It is possible that an error is only displayed for a short time, but after the 
acknowledgement it will disappear. In this case, it's recommended to 
switch off the control unit and switch it on again (reset by restarting). 

 

 

 

 

Summary of Contents for MultiStar CG10

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands