manualshive.com logo in svg

Gema MultiStar CG10, Operating Instructions And Spare Parts List

Share
Download
Gema MultiStar CG10 Operating Instructions And Spare Parts List Download Page 27

 

Rev. 00  08/17 

 

MultiStar CG10 

Start-up  

  27 

 

Start-up 

 

 

Preparation for start-up 

 

 

The gun control unit always starts up to the last configured 
settings. 

Basic conditions 

When starting up the gun control unit, the following general conditions 
impacting the coating results must be taken into consideration: 

– 

Gun control unit correctly connected 

– 

Gun correctly connected 

– 

Corresponding power and compressed air supply available 

– 

Powder preparation and powder quality 

 

System parameters 

The Gun control unit is configured by using the system parameters. This 
configuration will be saved in the equipment memory. These values can 
be adjusted and requested manually or by remote interface (CAN). 

Entering the system parameters 

1. 

Turn on the gun control unit with the 

ON

 key  

2. 

Hold 

 key down for 5 seconds 

–  The display switches to the following level: 

 

Summary of Contents for MultiStar CG10

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands