manualshive.com logo in svg

Gema MultiStar CG10, Operating Instructions And Spare Parts List

Share
Download
Gema MultiStar CG10 Operating Instructions And Spare Parts List Download Page 37

 

Rev. 00  08/17 

 

MultiStar CG10 

Operation  

  37 

 

Selecting the preset coating programs (Easy 
Mode only) 

 

1. 

Turn on the gun control unit with the 

ON

 key 

2. 

Press the corresponding application key. 

The arrow above the desired button lights up. 

 

 

 

The pre-defined application modes have preset values for high 
voltage and spray current: 

 

Application mode 

Preset µA 

Preset kV 

 

flat parts 

100 

100 

  

complicated parts 

22 

100 

 

overcoat 

10 

100 

3. 

The air values for total air, powder output and electrode rinsing air 
can be individually defined and are saved in the programs. 

 

Setting powder output and powder cloud 

The powder output depends on the selected powder output (in %), and 
the powder cloud on the selected total air volume.  
 

 

In Advanced Mode (P01=1), separate setpoints can be used for 
the powder output volume, total air and electrode rinsing air for 
each gun.  

–  The values displayed correspond to the guns which were 

selected with the relevant button on the additional panel.  

 

 

As a factory default value, a powder rate of 60% and a total air 
volume of 4 Nm³/h are recommended. 

–  If values are entered that the gun control unit cannot implement, 

then the operator is informed of this by a blinking in the relevant 
display and a temporary error message! 

Setting the total air volume 

1. 

 

 

Adjust the total air volume on the gun control unit with the 

T3/T4

 

keys 

– 

Adjust the total air volume according to the corresponding coating 
requests 

Summary of Contents for MultiStar CG10

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands