manualshive.com logo in svg

Gema MultiStar CG10, Operating Instructions And Spare Parts List

Share
Download
Gema MultiStar CG10 Operating Instructions And Spare Parts List Download Page 46

 

Rev. 00  08/17

 

46  

  Operation 

MultiStar CG10 

Checking the software version 

1. 

Press these two keys at the same time 

 

 

–  The status display is shown as long as the keys are held. 

 

RAM Reset 

The RAM reset enables a restore of factory settings of the gun control 
unit. All parameters (

except P00

) and correction values as well as all 

user-defined values in the Program mode and Preset mode will be 
overwritten with factory default values. An active keyboard lock will be 
deactivated. 
 

 

By resetting the RAM, all user-made settings will be set to factory 
default! 

 

1. 

Switch off the device 

2. 

Press the 

 key and hold it 

3. 

Switch on the control unit, the 

CLR

 display blinks 

 

 

4. 

Wait for approximately 5 seconds until 

CLR

 disappears 

5. 

Release the 

 key 

–  All values are reset. The control unit must be set-up again. 

 

 

 

Summary of Contents for MultiStar CG10

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands