gefran AD Quick Start Up Manual, Specification And Installation Download Page 53

Page: 53 / 142

ADV200 WA • Quick start up guide - Specification and installation

RS485
(XS)

RS485

RS232

PCI-COM

(S5T60)

Industrial PC
(with RS485)

RS232

USB

USB RS232 converter

(S5A20)

with

RS232

port

with

USB

port

RS485
(XS)

RS485

RS232

PCI-COM

(S5T60)

Shielded cable with connectors,

5 mt (8S8F59)

Shielded cable with connectors,

5 mt (8S8F59)

Shielded cable with

connectors,

5 mt (8S8F59)

Kit (S50T6) = Shielded cable 5 mt + PCI-COM

Figure 5.4.1.2: RS485 connection to the PC

Connection of an industrial PC with RS485

The following are required for connection:

• shielded cable for the

XS / RS485

connection (see figure 5.4.1.1), code

8S8F59

Connection to a PC with RS232 port

The following are required for connection:

• an optional

PCI-COM

(or PCI-485) adapter, code S560T.

• shielded cable for

XS / PCI-COM

(or PCI-485) connection, code 8S8F59, see

figure 5.4.1.1 .

Connection to a PC with USB port

The following are required for connection:

• an optional

PCI-COM

(or PCI-485) adapter, code S560T.

• an optional

USB/ RS232

adapter, code S5A20 (including the cable for USB

connection)

• shielded cable for the

XS / PCI-COM

(or PCI-485) connection, code 8S8F59,

see figure 5.4.1.1 .

5.4.2 Drive / RS485 port point-to-point connection (with insulation)

To make the connection with galvanic isolation, the

OPT-RS485-ADV

optional

card is required.

The card is equipped with a 9-pin D-SUB male receptacle connector which must

be inserted in the

connector of the ADV200 WA drive.

Connect terminals 1, 2 and 4 to the serial line as shown in the figure below; for

the connection from the serial line to the PC, the adapters indicated in paragraph

5.4.1 must be used.

Summary of Contents for AD















































































































































Search results

Summary of Contents for AD

Reviews:

Related manuals for AD

Brands by name

Popular brands

gefran AD, Quick Start Up Manual, Specification And Installation

Search results

Summary of Contents for AD

Reviews:

Related manuals for AD

Brands by name

Popular brands