gefran AD Quick Start Up Manual, Specification And Installation Download Page 83

Page: 83 / 142

ADV200 WA • Quick start up guide - Specification and installation

The analog output signal can be adjusted using

Analog out 1 scale

(PAR: 1808)

and

Analog out 2 scale

parameters (PAR:1810).

• Keypad

Use the

LOC / REM

key with the Enable input open (terminal 7 on terminal strip

T2) to control running, to stop and reverse the direction of rotation of the motor

using the operator keypad on the drive. Use the potentiometer or an analog signal

to control speed.

For information on how to use a digital speed reference, see the example on

chap-

ter 7.3.3

. The reference can have a positive or negative value, making it possible to

reverse the direction of rotation of the motor.

When the Enable input is closed, to enable motor running press

START.

The mo-

tor starts the acceleration ramp and moves to the speed set in the FWD direction.

With the motor running you can adjust the speed using the

Dig ramp ref 1

param-

eter (PAR: 600) and the acceleration/deceleration ramps using

Acceleration time

(PAR: 700) and

Deceleration time 0

(PAR: 702).

To change the direction of rotation press

FWD/REV

To stop the motor with the deceleration ramp, press

STOP

If the Enable contact is opened the inverter bridge is immediately disabled and the

motor stops for inertia

To return to control using the terminal strip commands and analog speed refer-

ence:

Stop the motor

Open the Enable terminal

Press

LOC / REM

key.

Note !

For more customizations and any information that is not included in this initial customization guide, see
the description of the parameters in this manual.

Summary of Contents for AD















































































































































Search results

Summary of Contents for AD

Reviews:

Related manuals for AD

Brands by name

Popular brands

gefran AD, Quick Start Up Manual, Specification And Installation

Search results

Summary of Contents for AD

Reviews:

Related manuals for AD

Brands by name

Popular brands