manualshive.com logo in svg

Gefen EXT-DP-EDIDP, User Manual, Page: 19 / 56

Share
Download
Gefen EXT-DP-EDIDP User Manual Download Page 19

page | 9

The table below provides a status summary of the Power LED.

LED

Status

Conditions

Power

Solid blue

• 

Detective is powered

• 

HPD is high

• 

EDID has been successfully written 

(to a EDID bank or the local input)

Solid red

• 

Bad EDID

• 

HPD is low

Flashing 

blue

• 

EDID is being read from sink

• 

EDID is being read from EDID bank

 

Passing HDCP Content

In order for the 

DisplayPort Detective Plus

 to pass HDCP content (e.g. Blu-ray, etc.), set 

DIP switch 4 to the ON (down) position.

After setting DIP switch 4 to the ON position, reboot the DisplayPort Detective Plus by 

disconnecting and then reconnecting the power. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Page Title

Operating the DisplayPort Detective Plus

DIP switch 4 in 

ON position

EDID Programming

IMPORTANT:  

When enabling or disabling HDCP pass-through, the 

DisplayPort Detective Plus

 must be power-cycled in order for the 

DIP switch setting to take effect.

Summary of Contents for EXT-DP-EDIDP

























































Reviews:

No comments