49-5000640 Rev. 0
Installation Preparation
IMPORTANT ELECTRICAL
SAFETY—READ
CAREFULLY
WARNING
RISK OF ELECTRIC SHOCK.
$OOHOHFWULFDOFRQQHFWLRQVDQGZLULQJ0867EH
installed by a qualified electrician.
)ROORZWKH1DWLRQDO(OHFWULFDO&RGH1(&DQGRU
local codes and ordinances.
)RUSHUVRQDOVDIHW\WKLV=RQHOLQHXQLWDQGFDVH
must be properly grounded.
3URWHFWLYHGHYLFHVIXVHVRUFLUFXLWEUHDNHUV
DFFHSWDEOHIRU=RQHOLQHLQVWDOODWLRQVDUHVSHFLILHGRQ
the nameplate of each unit.
• Do not use an extension cord with this unit.
• Aluminum building wiring may present special
problems—consult a qualified electrician.
• When the unit is not running there is still voltage to
the electrical controls.
• Disconnect the power to the unit before servicing by:
5HPRYLQJWKHEUDQFKFLUFXLWIXVHVRUWXUQLQJWKH
circuit breakers off at the panel.
2.
Disconnecting the power cord from the unit.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•
IMPORTANT –
Save these
instructions for local inspector’s use.
•
IMPORTANT –
Observe all governing
codes and ordinances.
•
Note to Installer –
Be sure to leave these
instructions with the owner.
•
Note to Owner –
Keep these instructions for
future reference.
•
3URSHULQVWDOODWLRQLVWKHUHVSRQVLELOLW\RIWKH
LQVWDOOHU&RPSOHWHGLQVWDOODWLRQRIWKH=RQHOLQH
shall not be accessible to the general public.
•
3URGXFWIDLOXUHGXHWRLPSURSHULQVWDOODWLRQLVQRW
covered under the Warranty.
•
7HDPOLIWLVUHFRPPHQGHGZKHQPRYLQJXQLW
•
<RX0867XVHDOOVXSSOLHGSDUWVDQGXVHSURSHU
installation procedures as described in these
instructions when installing this air conditioner.
Questions? Call 844-GE4-PTAC (or 844-434-7822 ) or
Visit our Website at:
GEAppliances.com
ELECTRICAL
REQUIREMENTS
NOTE: All field wiring must comply with NEC and
local codes. It is the responsibility of the installer
to ensure that the electrical codes are met.
:LUH6L]H
Use
ONLY
ZLUHVL]HUHFRPPHQGHG
for single outlet branch circuit
Fuse/Circuit
Breaker
8VH21/<W\SHDQGVL]HIXVHRU
+9$&5FLUFXLWEUHDNHULQGLFWHG
RQXQLWVUDWLQJSODWH3URSHURYHU
current protection to the units is the
responsibility of the owner.
Grounding
8QLW0867EHJURXQGHGIURPEUDQFK
circuit to unit, or through separate
ground wire provided on permanently
connected units. Be sure that branch
circuit is grounded.
:LUH6L]LQJ
8VHUHFRPPHQGHGZLUHVL]HJLYHQ
in tables and install a single branch
circuit. All wiring must comply with
local and national codes.
NOTE: Use copper conductors
only.
WARNING
RISK OF ELECTRIC SHOCK.
&DQFDXVHLQMXU\RUGHDWK7KLVDSSOLDQFHPXVWEH
properly grounded.
8VH21/<WKHZLULQJVL]HUHFRPPHQGHGIRUVLQJOH
outlet branch circuit.
3URSHUFXUUHQWSURWHFWLRQLVWKHUHVSRQVLELOLW\
of the owner.
NOTE:
Use copper conductors only.
Recommended Branch Circuit Wire Sizes*
Nameplate
Maximum Circuit
Breaker Size
AWG Wire Size**
$
$
$
AWG - American Wire Gauge
6LQJOHFLUFXLWEUHDNHUIURPPDLQER[
%DVHGRQFRSSHUZLUHVLQJOHLQVXODWHGFRQGXFWRU
DW
C
INST
ALLA
TION INSTRUCTIONS