GE SG 225 User Manual Download Page 50

Page: 50 / 79

Modifications reserved

Page 50/79

OPM_SGS_USM_M22_M30_2US_V010.doc

User Manual

SG Series 225 & 300 UL S2

3. Open the UPS Output Switch Q1 (Pos. O) and then press the “Load Off” button

•

The

load

is now supplied only through the

Manual Bypass Q2.

•

Rectifier

shuts down and all output and input

Contactors

are opened.

•

Press the

“MUTE”

key to reset the

alarm buzzer

The

Synoptic Diagram

must display the status

“

LOAD

SUPPLIED BY MANUAL BYPASS Q2

”.

4. Disconnect the Battery from the UPS by opening (Pos. O) the External Battery Switch or Fuses.

•

Wait

5 minutes

for DC-Link Capacitors discharge.

The

Load

is now powered from the

Utility

through

Manual Bypass Q2 (option)

END OF PROCEDURE

WARNING!

It will take a minimum of 5 minutes for the DC capacitors to discharge.
Open only the front door, do not open any other part of the UPS.

Summary of Contents for SG 225
















































































Search results

Summary of Contents for SG 225

Reviews:

Related manuals for SG 225

Brands by name

Popular brands

GE SG 225, User Manual

Search results

Summary of Contents for SG 225

Reviews:

Related manuals for SG 225

Brands by name

Popular brands