background image

4

Installation Preparation

 

IMPORTANT

(Please read carefully.)

The power cord of this appliance is equipped with 

DWKUHHSURQJJURXQGLQJSOXJZKLFKPDWHVZLWK

a standard three-prong grounding wall receptacle 

to minimize the possibility of electric shock. The 

customer should have the wall receptacle and 

FLUFXLWFKHFNHGE\DTXDOL¿HGHOHFWULFLDQWRPDNH

sure the receptacle is properly grounded and has 

correct polarity.
• Where a standard two-prong wall receptacle is 

encountered, it is the personal responsibility and 

obligation of the customer to have it replaced 

with a properly grounded three-prong wall 

receptacle.

Do not, under any circumstances, cut or remove 
the third (ground) prong from the power cord.

Do not use an extension cord or adapter plug with 

this appliance. Follow National Electrical Code or 

prevailing local codes and ordinances.
Location of Rating Label: on front of chassis of 

vent system.

This downdraft vent must be supplied with 120V, 

60 Hz. and connected to an individual, properly 

grounded branch circuit, protected by a 15- or 

20-ampere circuit breaker or time-delay fuse.
A properly grounded 3-prong receptacle should be 

located within reach of the vent’s two-foot power 

cord. 
• 

Gas Cooktops

If this vent is installed in combination with a GE or 

Monogram gas cooktop, it may operate from the 

same duplex outlet.

• 

Electric Cooktops

If this vent is installed in combination with a GE 

or Monogram electric cooktop, the vent must 
operate from a separate 120V outlet.

Locate the receptacle inside the cabinet on the right 

VLGHZDOOVHHLOOXVWUDWLRQ7KHUHFHSWDFOHFDQQRWEH

placed on the back of the cabinet wall where it may 

interfere with the downdraft plenum. 
The downdraft vent power cord is to be routed 

beneath the cooktop and routed away from heat 

generated by the cooktop.
Ensure that the cooktop is installed per 

manufacturer’s installation instructions.

POWER SUPPLY

Locate the Gas or Electrical 

Connection Only Within the 

Shaded Area

DO NOT Locate 

Gas or Electrical 

Connections within 

this Area

FXWRXWZLGWKIRUPRGHOV

FXWRXWZLGWKIRUPRGHOV

29-1/2" 

12" 

Electrical 

Outlet 12" 

Above 

Cabinet 

Floor

Summary of Contents for PVB94













Reviews: