background image

3

Safety Information

WARNING:

 

TO REDUCE THE RISK OF 

FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, 
OBSERVE THE FOLLOWING.

• 

Installation work and electrical wiring must be 

GRQHE\DTXDOL¿HGSHUVRQVLQDFFRUGDQFHZLWK
DOODSSOLFDEOHFRGHVDQGVWDQGDUGVLQFOXGLQJ¿UH

rated construction.

• 

6XȻFLHQWDLULVQHHGHGIRUSURSHUFRPEXVWLRQDQG
H[KDXVWLQJRIJDVHVWKURXJKWKHÀXHFKLPQH\RI

fuel burning equipment to prevent back drafting. 

Follow the heating equipment manufacturer’s 

guidelines and safety standards such as those 

published by the National Fire Protection 

$VVRFLDWLRQ1)3$DQGWKH$PHULFDQ6RFLHW\

for Heating, Refrigeration and Air Conditioning 

(QJLQHHUV$6+5$(DQGWKHORFDOFRGHDXWKRULWLHV

• 

When cutting or drilling into wall or ceiling, do not 

damage electrical wiring and other hidden utilities.

• 

Ducted fans must always be vented to the 

outdoors.

CAUTION:

 

7RUHGXFHWKHULVNRI¿UHDQG

to properly exhaust air, be sure to duct air outdoors. 

Do not vent exhaust air into spaces within walls or 

ceilings or into attics, crawl spaces or garages.

WARNING:

 

TO REDUCE THE RISK OF 

FIRE, USE ONLY METAL DUCTWORK.

• 

:KHQDSSOLFDEOHLQVWDOODQ\PDNHXSUHSODFHPHQW

air system in accordance with local building code 

requirements. Visit GEAppliances.com for available 

makeup air solutions.

•  PVC sewer pipe can be used as duct under concrete 

slab if allowed by local code board.

Summary of Contents for PVB94













Reviews: