GE PVB94 Installation Instructions Manual Download Page 2

2

Safety Information

BEFORE YOU BEGIN

 

Read these instructions completely and carefully.

•  

IMPORTANT

³

Save these instructions for local 

inspector’s use. 

•  

IMPORTANT

³

Observe all governing codes and 

ordinances.

•  

Note to Installer

³

Be sure to leave these instructions 

with the Consumer.

•  

Note to Consumer

³

Keep these instructions with your 

Owner’s Manual for future reference.

•  

Skill level

³

Installation of this appliance requires a 

qualified installer or electrician.

•  Proper installation is the responsibility of the installer. 

Product failure due to improper installation is not covered 

under the warranty. See Owner’s Manual for warranty 

information.

GROUNDING INSTRUCTIONS

 This appliance must be grounded. In the event of an 

electrical short circuit, grounding reduces the risk of electric 

shock by providing an escape wire for the electric current. 

This appliance is equipped with a cord having a grounding 

wire with a grounding plug. The plug must be plugged into 

an outlet that is property installed and grounded.

WARNING:

Improper grounding can result in a risk of electric shock.
Consult a qualified electrician if the grounding instructions 

are not completely understood, or if doubt exist as to 

whether the appliance is properly grounded.
Do not use an extension cord. If the power supply cord is too 

short, have a qualified electrician install an outlet near the 

appliance.
For Monogram local service in your area, 1.800.444.1845.
For Monogram Service in Canada, call 1.800.561.3344.
For Monogram Parts and Accessories, call 1.800.626.2002.
If you received a damaged vent system, you should contact 

your dealer.

“If you have questions, call 800.GE.CARES or visit our website at: GEAppliances.com”

PARTS SUPPLIED

Open the carton and remove parts package.

Check contents to be sure all pieces are present.

TOOLS AND MATERIALS REQUIRED

• Safety glasses

‡/DUJHÀDWEODGHVFUHZGULYHU

• Jigsaw

• Carpenter’s square

• Ductwork to suit the installation

• Level

REMOVE PACKAGING

• Remove the shipping materials and the carton; 

set carton aside. The carton can be used as a pad 

when changing or adjusting vent direction.

4 Stabilizing Brackets 

With Screws

1 Remote Switch

2 Filters

1 Wire and White 

Connector

Summary of Contents for PVB94













Reviews: