GE Profile ENERGY STAR WPDH8800J Technical Support Download Page 65

Page: 65 / 68

Error Codes (cont.)

Check integrity of wire connections between the Motor Drive
Control and the motor.

Clear fault and run cycle. If fault persists and reappears,
replace the motor drive.

Open circuit in
any of three
motor phases
detected
No speed info
present and
bridge will be
turned off
immediately
Motor will coast
down
Drive will
preserve non-
zero speed info
during the stop
check stage

E15 Open Circuit

•Check valve for any signs of leaks.
•Check integrity of Water Level Sensor. Replace if
necessary.

Overflow level
was reached

E14 Overflow Error

Action

Description

Error Code

CONFIDENTIAL AND PROPRIETARY INFORMATION-NOT FOR PUBLIC DISCLOSURE. September 2008

Summary of Contents for Profile ENERGY STAR WPDH8800J





































































Search results

Summary of Contents for Profile ENERGY STAR WPDH8800J

Reviews:

Related manuals for Profile ENERGY STAR WPDH8800J

Brands by name

Popular brands

GE Profile ENERGY STAR WPDH8800J, Technical Support

Search results

Summary of Contents for Profile ENERGY STAR WPDH8800J

Reviews:

Related manuals for Profile ENERGY STAR WPDH8800J

Brands by name

Popular brands