GE Profile ENERGY STAR WPDH8800J Technical Support Download Page 54 | Manualshive

Page: 54 / 68

54

Service Test Mode (cont.)

Checks the control status of the prime status of the
pumps and allows the user to change/reset the
prime status.

t20 Bulk Primed Status

Manually initiates the priming of the Smart
Dispenser pumps.

t19 Bulk Manual Priming

Tests each spin speed of the washer.

Note:

No

out-of-balance detection will be performed here,
so the washer will spin up regardless of any out-of
balance condition in the drum.

t18 AutoSpin Profile

Verifies all the Smart Dispenser Sensors work.

t17 Bulk Sensors Test

Verifies all the Smart Dispenser Pumps work.

t16 Bulk Pumps Test

Verifies the dispenser motor works and can locate
all 4 dispenser positions.

t15 Dispenser Test

Description

Test Mode

CONFIDENTIAL AND PROPRIETARY INFORMATION-NOT FOR PUBLIC DISCLOSURE. September 2008

«
...
52
53
54
55
56
...
»

Summary of Contents for Profile ENERGY STAR WPDH8800J





































































Reviews:

No comments

Related manuals for Profile ENERGY STAR WPDH8800J

Brand: Zanussi Pages: 20

Brand: Zanussi Pages: 34

Brand: Jenn-Air Pages: 40

Brand: Jenn-Air Pages: 3

Brand: Midea Pages: 10

Brand: Spitwater Pages: 22

Brand: ETNA Pages: 100

Brand: Metos Pages: 52

Brand: Gaggenau Pages: 19

Brand: Insinger Pages: 104

Brand: Champion Pages: 33

Brand: Smeg Pages: 31

Brand: Russell Hobbs Pages: 28

Brand: Black Max Pages: 44

Brand: Samsung Pages: 88

Brand: Samsung Pages: 88

Brand: Samsung Pages: 128

Brand: Samsung Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands