GE Profile ENERGY STAR WPDH8800J Technical Support Download Page 57

Page: 57 / 68

Diagnostic Tests (cont.)

Fills with cold water. Display shows “Cold Water On”

Enter

Cold Water
Valve Test

t12

Drains and returns to service mode screen

Start

t11

Hot Water
Valve Test

Returns to service mode screen

Power

Unit tumbles

Enter

Tumble Test

t13

Drains and returns to service mode screen

Power

Fills with hot water. Display shows “Hot Water On”

Enter

Drains and returns to service mode screen

Power

Displays “baseline” and “current” temperature. Unit fi lls with
water and gets heated

Enter

Temp Sensor
and Heater

t10

Drains and returns to service mode

Power

Fills to overflow level. Display shows “Normal Wash Level”
until fill is complete. When overflow level is reached, the
pump begins to drain out the water.

Start

(cont.)

t09

Sequence

Service Mode Test

CONFIDENTIAL AND PROPRIETARY INFORMATION-NOT FOR PUBLIC DISCLOSURE. September 2008

Summary of Contents for Profile ENERGY STAR WPDH8800J





































































Search results

Summary of Contents for Profile ENERGY STAR WPDH8800J

Reviews:

Related manuals for Profile ENERGY STAR WPDH8800J

Brands by name

Popular brands

GE Profile ENERGY STAR WPDH8800J, Technical Support

Search results

Summary of Contents for Profile ENERGY STAR WPDH8800J

Reviews:

Related manuals for Profile ENERGY STAR WPDH8800J

Brands by name

Popular brands