manualshive.com logo in svg

GE Monogram ZWVS1000SR, Installation Instructions Manual

Share
Download
GE Monogram ZWVS1000SR Installation Instructions Manual Download Page 31

31

Moisture is leaking from the front fan vents

Possible Cause

Recommended Solution

The internal condensation

Call 1-877-234-WINE. Disassembly of the unit will void

drain is blocked

the warranty.

Excessive humidity or 

Install external drain tube to outlet at the front.

blocked drain

Build up of dust 

Vacuum intake and exhaust vents.

Unit does not cool the wine vault

Possible Cause

Recommended Solution

Inadequate door seal

Check the door seal for gaps.  

Cooling unit is not installed

Check the installation of the unit. Make sure insulation

properly

tape is installed properly.

Insufficient ventilation

Temperature of the surrounding room cannot exceed 85°F.

Unit is icing up

Possible Cause

Recommended Solution

Faulty thermostat

Call 1-877-234-WINE. 

Unit low on refrigerant

Call 1-877-234-WINE. 

Unit not running or making a clicking sound

Possible Cause

Recommended Solution

Local electrical circuit

Check the power supply.

Designed to shut-off

The unit will shut-off 5 minutes every 90 minutes for an 
automatic defrost.

COOLING UNIT

Summary of Contents for Monogram ZWVS1000SR

































Reviews:

No comments

Brands by name

Popular brands

Load more brands