GE Mini Telemetry Operation And Maintenance Manual Download Page 44

Page: 44 / 71

2049809-001 Rev B

Chapter 4: Installation and Setup

Monitoring via Telemetry

This section provides a brief overview of telemetry monitoring procedures. Refer to the “Maternal/Fetal

Monitoring Operator’s Manual” for patient application information. Also refer to your monitor’s operator manual.

Suggestions for Ambulatory Monitoring

IMPORTANT :

DESIGNATED AREAS—Show the patient the areas that are within signal range and where signal reception is

clear. The designated area is determined at the time of installation.

Following are the suggestions for ambulatory monitoring:

1. Instruct the patient to wear the transmitter with the enclosure faced towards the receiver when possible.

2. Adjust the carrying strap to a comfortable length.

3. Encourage the patient to walk in a smooth, gliding motion. It is preferable to slide feet instead of moving

quickly which may cause bouncing and artifact.

4. Instruct the patient, following each fetal movement, to listen via the headset or speaker, for continued

“pickup” of fetal heart rate tones.

NOTE

: Transducers with short cables are available. Contact your Information Technologies Sales representative

Perform the following precautionary measures during ambulatory monitoring:

Illustration

Description

1. Make sure the transducer cables are not hanging

loosely, the patient is in danger of tripping over

the cables.

Summary of Contents for Mini Telemetry



































































Search results

Summary of Contents for Mini Telemetry

Reviews:

Related manuals for Mini Telemetry

Brands by name

Popular brands

GE Mini Telemetry, Operation And Maintenance Manual

Search results

Summary of Contents for Mini Telemetry

Reviews:

Related manuals for Mini Telemetry

Brands by name

Popular brands