GE Mini Telemetry Operation And Maintenance Manual Download Page 38

Page: 38 / 71

2049809-001 Rev B

Chapter 4: Installation and Setup

Performing a Functional Checkout

Initial Conditions

Step

Instructions

Connect the receiver to the monitor as described in

“Connecting the Receiver and Monitor” section earlier

in this chapter.

Turn on the transmitter, receiver and monitor attached

to the receiver.

Testing the Radio Frequency

Perform the following steps to test the radio frequency.

Step

Instructions
Instructions to Test the Radio Frequency:

1. Check the status of the Signal indicator

the receiver:
•

Continuous Green: Indicates that the receiver

is accepting the radio frequency signals from

the transmitter and the signal strength is

good.

•

Flashing Green

: Indicates the signal strength

is weak or marginal.

2. Check the status of the Battery indicator

the receiver:
•

Off

: The transmitter battery is adequately

charged.

•

Blinking/Continuous Red: The transmitter

battery is low and should be recharged before

further patient use.

Summary of Contents for Mini Telemetry



































































Search results

Summary of Contents for Mini Telemetry

Reviews:

Related manuals for Mini Telemetry

Brands by name

Popular brands

GE Mini Telemetry, Operation And Maintenance Manual

Search results

Summary of Contents for Mini Telemetry

Reviews:

Related manuals for Mini Telemetry

Brands by name

Popular brands