manualshive.com logo in svg

GE MG-101, User Manual

Share
Download
GE MG-101 User Manual Download Page 6

Preface

iv

MG-101 User’s Manual

Environmental Compliance

Waste Electrical and Electronic Equipment (WEEE) Directive

GE Measurement & Control is an active participant in Europe’s 

Waste Electrical and Electronic Equipment

 (WEEE) 

take-back initiative, directive 2002/96/EC.

The equipment that you bought has required the extraction and use of natural resources for its production. It may 
contain hazardous substances that could impact health and the environment.

In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural 
resources, we encourage you to use the appropriate take-back systems. Those systems will reuse or recycle most of the 
materials of your end life equipment in a sound way.

The crossed-out wheeled bin symbol invites you to use those systems.

If you need more information on the collection, reuse and recycling systems, please contact your local or regional 
waste administration.

Visit 

http://www.ge-mcs.com/en/about-us/environmental-health-and-safety/1741-weee-req.html

 for 

take-back instructions and more information about this initiative.

Summary of Contents for MG-101



































Reviews:

No comments

Brands by name

Popular brands

Load more brands