GE MAC 600 SPY Service Manual Download Page 63

Page: 63 / 127

Revision G

MAC

600

4-13

2047426-002

Maintenance:

Preparing System for FRU Replacement

5. Verify the new Earth Cable routing is as shown in the following

photo.

6. Close the device and do the functional and safety testing for the

power supply and Main PCB after the replacement of the FRU. See

“Functional Checkout”

on page 4-22.

7. Open the printer door and Connect the power cord to the ACDC

adaptor and adaptor output to the unit. Check for the resistance
between power cord ground and printer metal portion. If the value of
resistance is greater than 1 Ohm, then it results in failure. Verify the
connections if failure happens.

8. Proceed to

“Changing the Product Label”

Changing the Product Label

The product label is located on the back panel, as shown in the following
photo.

Summary of Contents for MAC 600 SPY
































































































































Search results

Summary of Contents for MAC 600 SPY

Reviews:

Related manuals for MAC 600 SPY

Brands by name

Popular brands

GE MAC 600 SPY, Service Manual

Search results

Summary of Contents for MAC 600 SPY

Reviews:

Related manuals for MAC 600 SPY

Brands by name

Popular brands