GE IC3645SP4U450N10 Installation And Operation Manual Download Page 27

Page: 27 / 69

DIAGNOSTIC STATUS CODES

SX TRANSISTOR CONTROL

Page

October 2002

TRACTION

STATUS CODE

DESCRIPTION OF STATUS

CAUSE OF STATUS INDICATION

-15

Battery voltage is too low or control
card is mis-adjusted.

This status code will be displayed when the battery
volts are less than 1.95 volts per cell at initial key
switch on. See table below.

MEMORY R CALL

CORRECTIVE ACTIONS

TROUBLE-SHOOTING DIAGRAM

Circuits valid

for

Traction

Controller

SYMPTOM

Control will not operate.

POSSIBLE CAUSE

Discharged battery

Check battery for proper open circuit voltage
as shown in “Trouble Shooting Diagram”,
charge battery, if required.

Defective battery

Check each battery cell for proper voltage
(greater than 1.95 volts at cell). Replace or
repair battery.

Incorrect control card adjustment.

Check Function 15 for proper adjustment for
battery being used. See Handset instruction
sheet for details. Adjust to proper settings.

Check “minimum” battery volts at P1 and NEG.

NEG

FU5

NOMINAL
BATTERY

VOLTAGE

MINIMUM

LIMIT VOLTS

AT 1.95 VDC

PER CELL

23.4

78.0

46.8

70.2

35.1

TRACTION

STATUS CODE

DESCRIPTION OF STATUS

CAUSE OF STATUS INDICATION

-16

Battery voltage is too high or control
card is mis-adjusted.

This status code will be displayed when the battery
volts are greater than 2.4 volts per cell at initial key
switch on. See table below.

MEMORY R CALL

CORRECTIVE ACTIONS

TROUBLE-SHOOTING DIAGRAM

Circuits valid

for

Traction

Controller

SYMPTOM

Control will not operate.

POSSIBLE CAUSE

Incorrect control card adjustment
Check Function 15 for proper
adjustment for battery being used. See
Handset instructions for details. Adjust
to proper setting.

Battery over charged or incorrect
battery used.

Check battery for proper open circuit
voltage per table at right. If voltage is
excessive, check battery charger for
proper output voltage.

Check “maximum” battery volts at P1
and NEG.

NEG

FU5

NOMINAL
BATTERY

VOLTAGE

MAXIMUM

LIMIT VOLTS

AT 1.95 VDC

PER CELL

28.8

100.8

57.6

86.4

43.2

Summary of Contents for IC3645SP4U450N10






































































Search results

Summary of Contents for IC3645SP4U450N10

Reviews:

Related manuals for IC3645SP4U450N10

Brands by name

Popular brands

GE IC3645SP4U450N10, Installation And Operation Manual

Search results

Summary of Contents for IC3645SP4U450N10

Reviews:

Related manuals for IC3645SP4U450N10

Brands by name

Popular brands