GE IC3645SP4U450N10 Installation And Operation Manual Download Page 26

Page: 26 / 69

DIAGNOSTIC STATUS CODES

SX TRANSISTOR CONTROL

Page

October 2002

TRACTION

STATUS CODE

DESCRIPTION OF STATUS

CAUSE OF STATUS INDICATION

-09

Both the forward and reverse
directional switches are closed at the
same time.

This status code will be displayed when P4 and P5
are greater than 60% of battery volts at the same
time.

MEMORY R CALL

CORRECTIVE ACTIONS

TROUBLE-SHOOTING DIAGRAM

Circuits valid

for

Traction

Controller

SYMPTOM

Control will not operate.

POSSIBLE CAUSE

Forward or reverse directional switch welded
closed or mis-adjusted to be held closed.

Replace or adjust directional switches to
insure that they open when directional switch
is returned to neutral.

Short circuit between battery positive and P4
and/or P5.

Disconnect wires from P4 and P5 and check
wire for short circuit to positive side of
directional switch.

Defective Control

Disconnect wires and measure voltage at P4
and P5. Voltage should be less than 60% of
battery volts.

KEY

SWITCH

P17

REVERSE SW

RWARD SW.

SEAT

ART

TRACTION

STATUS CODE

DESCRIPTION OF STATUS

CAUSE OF STATUS INDICATION

-11

Start switch closed on power up after
initial key switch closure.

This status code will be displayed when P3 is greater
than 60% of battery voltage when the key switch is
closed.

MEMORY R CALL

CORRECTIVE ACTIONS

TROUBLE-SHOOTING DIAGRAM

Circuits valid

for

Traction

Controller

SYMPTOM

Control will not operate.

POSSIBLE CAUSE

Start switch input mis-adjusted or defective.

Input voltage at P3 should be less than 60% of
battery volts at key switch closing. Adjust or
replace accelerator unit to insure that the
voltage at P3 is less than 60% of battery volts
before closing the start switch.

Short circuit between battery positive and P3 in
start switch input circuit.

Disconnect wire from P3. Check for short
circuit from this wire to battery positive.

Defective control.

Disconnect wire from P3. Measure voltage
from P3 to negative. Voltage should be zero,
if not, replace control.

KEY

SWITCH

P17

REVERSE SW

RWARD SW.

SEAT

ART

Summary of Contents for IC3645SP4U450N10






































































Search results

Summary of Contents for IC3645SP4U450N10

Reviews:

Related manuals for IC3645SP4U450N10

Brands by name

Popular brands

GE IC3645SP4U450N10, Installation And Operation Manual

Search results

Summary of Contents for IC3645SP4U450N10

Reviews:

Related manuals for IC3645SP4U450N10

Brands by name

Popular brands