manualshive.com logo in svg

GE Homespring UF 100, Operation Manual

Share
Download
GE Homespring UF 100 Operation Manual Download Page 9

Backpulse 

Tank

Digital Air 

Pressure 

Gauge

Valve Cap

fiGUrE 11 

fiGUrE 10 

Mark mounting hole 

locations 

Anchor this hole of the Bracket 

assembly to the wall stud first 

36” Vertical

Clearance

FigUre 9 

  

•

  Swing opposite end of the Bracket assembly 

 

    upward. Level the Bracket. Mark the locations of 

 

    the remaining three anchoring bolts with a pen 

 

    or pencil.

 

•

  Lower the unattached end of the Bracket 

 

    assembly back to the floor.

 

•

  Pre-drill the three holes for the remaining three 

 

    2½” anchoring bolts at the marked locations.

   

• 

 Lift Bracket assembly up again, insert the 

 

    three 2½” anchoring bolts, and tighten all four 

 

    anchoring bolts.

 

Wall MOUnTinG

 

The Bracket assembly must be mounted directly 

 

to the wall studs or the two pieces of 2x4 lumber 

 

installed earlier. The four 2½” wall-mounting 

 

anchoring bolts are for wood studs only. If the wall 

 

is made of concrete, use appropriate concrete 

 

bolts for this installation.

  

• 

Mark the first hole location on the stud or lumber. 

 

    Ensure that all spacing requirements are   

 

    satisfied.

 

• 

 Drill a hole suitable for the supplied 2½” 

 

    anchoring bolt.

 

•

  Leaving one end of the Bracket assembly on the 

   

    ground for support, lift the opposite end of the 

  

    Bracket up, align the top mounting hole on the 

 

    Bracket assembly with the pre-drilled hole on the   

 

    wall stud, and secure the Bracket assembly with 

 

    one 2½” anchoring bolt. Do not tighten this bolt 

 

    completely.

4

b

The System is shipped fully assembled, except for  

the System Base.  Attach the System Base to the Back-

pulse Tank, using the supplied 

3/8” bolts and washers.

1

The Backpulse Tank has been pre-pressurized to ap-

proximately 30-35 psi from the factory. Confirm the Backpulse 

Tank pressure. If the Backpulse Tank pressure is less than 30 

psi, add air using a pump. Recheck the pressure after 15 min-

utes to ensure that there are no leaks in the Backpulse Tank.

3

The pressure may require adjustment depending 

on the water system of the home. Refer to the Table below 

to ensure proper tank pressure.  Air can be added or 

released from the Air Bladder Valve as required.

4

 

NOTE: For 

 

UFC 207, UF 207, UFC 209, UF 209,  UFC 

211, and UF 211 models

, cut open the plastic bag before 

standing the System upright.

Stand the System upright carefully. 

2

WARNING!

Handle the System with care. The outside surfaces of the 

System may be slippery with a food-grade preservative 

used in the manufacturing process.

System installation

9

WARNING!

If the Backpulse Tank has less than 20 psi of pressure, the 

integrity test will fail.

Only check the Backpulse Tank when the System is 

depressurized.

Summary of Contents for Homespring UF 100












































Reviews:

No comments

Brands by name

Popular brands

Load more brands