3/4”x1/4”
Bushing
3/4” Brass
Tee
Check
Valve
Mini Ball Valve
with Plug
Outlet port
of System
3/4” MNPT
Nipple
3/4” poly
Nipple
Stainless Steel
Flex Hose
3/4” MNPT
Nipple
Outlet fitting assembly
UF100 with
optional Surface
Water Option Kit
model only
fiGUrE 15
Metal
Support
Strap
fiGUrE 19
Fasten
System
to End Cast Iron
Stand here
Channel
on the System
Attach foam gasket
to concave feature on
the End Cast Iron Stand
Tab on the
Middle Cast
Iron Stand
fiGUrE 18
Outlet fitting assembly
Mini Ball Valve
with Plug
Inlet/Outlet
Fitting
Stainless Steel
Flex Hose
For models
equipped with
Surface Water
Option Kit only
3/4” MNPT
Nipple
Check
Valve
Outlet port
of System
fiGUrE 17
inlet fitting assembly
Mini Ball Valve
with Plug
Inlet/Outlet
Fitting
Stainless Steel
Flex Hose
For models
equipped with
Surface Water
Option Kit only
Inlet Solenoid
Valve
3/4” MNPT
Nipple
Inlet port of
System
fiGUrE 16
7
a
For UFC 207, UF 207, UFC 209, UF 209, UFC 211,
and UF 211 models, the two Inlet/Outlet Fitting assemblies
are shipped pre-assembled, with the Mini Ball Valves and
Plugs already installed. Ensure that the Teflon® tape at both
threaded ends are in good condition. Assemble the Inlet and
Outlet Fitting assemblies as shown.
6
b
7
a
6
a
6
a
UFC 207, UF 207, UFC 209, UF 209, UFC 211, and
UF 211
models, install the Drain Solenoid Valve (normally
closed) to the ½” Nipple to the Drain port of the System.
The directional arrow on the Drain Solenoid Valve must
point in the direction of the water flow (i.e. away from the
System). Install the Nylon Elbow to the flow exit port of the
Drain Solenoid Valve.
Horizontally-mounted Systems:
Install the ½” Nipple and the ½” Brass Elbow
provided in
the Horizontal Mounting Kit at the Drain port of the System.
Install the Drain Solenoid Valve to the ½” Brass Elbow
using another ½” Nipple.
7
b
For UFC100, UF100, and UF100 with optional
Surface Water Option Kit models, connect the Drain
Solenoid Valve (normally closed) to the 3/4” Nipple at the
Drain port of the System. The directional arrow on the Drain
Solenoid Valve must point in the direction of the water
flow (i.e. away from the System). Thread the Nylon Elbow
to the water flow exit port of the Drain Solenoid Valve.
7
a
The System Base is not required in this installation. Peel
off the adhesive backing on the foam gasket supplied in
the Horizontal Mounting Kit. Attach the foam gasket to the
concave feature on the End Cast Iron Stand.
8
applicable to Horizontally-mounted Systems
The directional arrow on the Check Valve must point in the
direction of the water flow.
The directional arrow on the Check Valve must point in the
direction of the water flow.
The directional arrow on the Inlet Solenoid Valve must point
in the direction of the water flow.
Lift up and place the System in the Bracket. Orient the
System to make the Inlet, Drain, and Outlet ports facing
downward. Ensure that the channel on the back of the
System locks into the tab on the Middle Cast Iron Stand.
Using two of the 3/8” bolts supplied with the System, fasten
the bottom of the System to the cross bar on the End Cast
Iron Stand. The Middle Cast Iron Stand is attached to the
Cast Iron Cross Member by two ¼” bolts and lock nuts.
Unscrew the ¼” bolt and lock nut closest to the System.
Position the semi-circular Metal Support Strap over the Sys
-
tem. Align the holes on the Metal Support Strap with the holes
on the Middle Cast Iron Stand. Reusing the ¼” bolt and lock nut
from the last step, fasten one end of the Metal Support Strap to
the Middle Cast Iron Stand. Use the remaining ¼” bolt and lock
nut supplied in the Horizontal Mounting Kit to fasten the other
end of the Metal Support Strap to the Middle Cast Iron Stand.
11
