The following list of tools and supplies are required for the
completion of this installation:
Tools (not provided)
Slip joint pliers 12”
Knife
Pipe Wrench 12”
Air pump
Adjustable wrenches
¼” Hex key
Torpedo Level
Torch with gas
Fine slot drivers
Masonry Drill with 3/8” bit
Phillips drivers: #0,1
Robertson drivers: #1,2
Nut drivers:5/16, 3/8
Snips
Supplies Required (not provided)
Copper pipe
Pen or pencil
Assorted Copper fittings Funnel
Flux and flux brush
Hose clamps
Solder (Lead free)
Suspension strap
Tie wraps or cable ties
Ground wire
Teflon® tape or pipe dope (for potable water)
5/8” hose for drain (comply with local plumbing code)
3 water shut-off valves (same size as install piping)
Unscented Chlorine Bleach- 5-6% or 12%
2’ x 2’ patio stones (required only for heated floor)
Tools supplied with Integrity Test Kit
Integrity Tester
Housing Wrench
Cap Wrench
Two Pressure Gauges
Two 1/4” tubings
Digital Air Pressure Gauge
Silicon Lubricant - DOW CORNING 111
Spare parts (Recommended)
AA batteries
Stainles Steel Flex Hose
Inlet Solenoid Valve
Drain Solenoid Valve
Air Relief Valve
O-ring
1/4” Mini Ball Valve with Plug
Advanced Plus Controllers
(Applicable to UFC100, UF100, and UF100 with op-
tional Surface Water Option Kit only):
¾” Brass Tees
FNPT, ¾” MNPT Nipple, ¾” poly Nipple, ¾”x¼” Bushing.
(Applicable to UFC207, UFC209, UF209, UFC209D, UF209D,
UFC211, and UF211 only):
¾” Inlet/Outlet Fitting, ½” Nipple.
UFC100
System (pre-assembled)
System Base
Base Controller
Transformer (120VAC)
Carbon Prefilter
Two Stainless Steel Flex
Hoses
Inside the bubble bag:
1 – Drain Solenoid Valve
(Normally Closed)
1 – Nylon Elbow
2 – ¾” Brass Tees
2 – ¾” Brass Bushings
2 – ¼” Mini Ball Valves
with Plugs
2 – ¾” Brass Nipples
3 – ¼” x 2 ½” anchors
3 – shims
3 – washers
3 – 3/8” bolts
1 – Air Relief Valve
UF100
System (pre-assembled)
System Base
Base Controller
Transformer (120VAC)
Stainless Steel Prefilter
Two Stainless Steel Flex
Hoses
Inside the bubble bag:
1 – Drain Solenoid Valve
(Normally Closed)
1 – Nylon Elbow
2 – ¾” Brass Tees
2 – ¾” Brass Bushings
2 – ¼” Mini Ball Valves
with Plugs
2 – ¾” Brass Nipples
3 – ¼” x 2 ½” anchors
3 – shims
3 – washers
3 – 3/8” bolts
1 – Air Relief Valve
UF100 with optional Surface Water Option Kit
System (pre-assembled)
System Base
Advanced Controller
Transformer (120VAC)
Stainless Steel Prefilter
Two Stainless Steel Flex Hoses
External Prefilter Housing
External Prefilter cartridge (30-micron nominal)
Wall Bracket Kit
Inside the bubble bag:
1 – Inlet Solenoid Valve (Normally Open)
1 – Drain Solenoid Valve (Normally Closed)
1 – Nylon Elbow
2 – ¾” Brass Tees
2 – ¾” Brass Bushings
3 – ¼” Mini Ball Valves w/ Plugs
4 – ¾” Brass Nipples
3 – ¼” x 2 ½” anchors
3 – shims
3 – washers
3 – 3/8” bolts
1 – Air Relief Valve
1 – Check valve
2 – 1” MNPT x ¾” FNPT PVC
Reducer Bushings
When treating surface water sources, an External Prefilter
of 25-microns nomimal mesh size is required. Failure to
provide this level of prefiltration may lead to System dam
-
age and will void the warranty. A damaged System may
cause serious personal injury, illness, and/or death.
WARNING!
Tools used to install the System should be maintained
in sterile condition so that the risk of cross-contamina-
tion is minimized. Bacteria, parasites, and viruses can
live for long periods of time. As a result, dangerous
organisms can be carried from one installation or mainte-
nance site to another and may potentially cause serious
personal injury, sickness and/or death. Proper tool care
and disinfection procedures will minimize these risks.
WARNING!
Ball valves are recommended for use as the Bypass,
Inlet and Outlet Valves. Gate valves have a ten
-
dency to leak, allowing unfiltered water to mix with
filtered water. The result may cause personal injury,
sickness and/or death.
WARNING!
Tools, Supplies and Parts
System Part list
6
