manualshive.com logo in svg

GE Interlogix NetworX NX-8, Installation And Startup

The GE Interlogix NetworX NX-8 is a top-notch security system designed to safeguard your home or business. With its comprehensive Installation Manual, you can easily set up and customize the system to meet your specific needs. Download the user manual for free from our website and enjoy the peace of mind you deserve.

Share
Download
background image

NX-8 Commercial Fire

22

Segment 2

1 = On if siren driver should be a voltage output. Off if on board siren driver enabled.
2 = On if siren sounds for expander trouble (required for UL installations).
3 = On for Immediate Restore by zone. Off for zones to restore only when siren is off.
4 = On if Dynamic Battery Test performed at arming. Off if performed at disarming. (Loc. 40)
5 = On if Battery Missing Test is performed every 12 seconds.
6 = On if Manual Bell Test performed during [

r

]-[4] test function.

7 = On if Manual Communicator Test performed during [

r

]- [4] test function.

8 = On if Box Tamper terminals on the control panel are enabled.

Segment 3

1 = On if

Box Tamper

report enabled.

2 = On if

AC Fail

reporting enabled.

3 = On if Low Battery reporting enabled.
4 = On if Aux. Power Overcurrent report enabled.
5 = On if Siren Supervision report enabled.
6 = On if Telephone Line Cut report enabled.
7 = On if Ground Fault Detection report enabled.
8 = On if Expander Trouble reporting enabled.

Segment 4

1 = On if Fail To Communicate report enabled.
2 = On if Log Full report enabled.
3 = On if Autotest report enabled.
4 = On if Start/End programming report enabled.
5 = Reserved.
6 = On if Sensor Low Battery report enabled.
7 = On if Sensor Missing report enabled.
8 = Reserved.

Segment 5

1 = On enables Lost Clock “Service Required” message.
2 = Reserved
3 = On disables On-Board 8 zones.
4 = On will allow two trips on same cross-zone to activate an alarm.
5 = On will not allow zones that are force armed to report bypass.
6 = On enables Silent Exit option.
7 = Use internal crystal for clock.
8 = Disable Temporal Siren on Fire. NOTE: DO NOT disable for UL listed systems.

 

LOCATION 38 -

SWINGER SHUTDOWN

COUNT

Location 38 contains the number of trips during an arming cycle that the NX-8-CF will allow before bypassing a zone.
The count determination is described in the GLOSSARY on page 6. NOTE: For UL installations, this feature shall
be disabled.

 

LOCATION 39 -

KEYPAD SOUNDER CONTROL

(1 segment, feature selection data)
Segment 1

1 = On if keypad sounds for

A

Telephone Line Cut

@

when the system is armed.

2 = On if keypad sounds for

A

Telephone Line Cut

@

when disarmed.

3 = On if keypad sounds upon AC Power Failure.
4 = On if keypad sounds when a Low Battery is detected.
5 = On if keypad sounds during

Cross Zone

trip time.

6 = On if keypad sounds for zone and

box tamper

s.

7 = Reserved.
8 = On if keypad sounds for expander trouble (required for UL installations).

 

LOCATION 40 - SYSTEM TIMERS
(10 segments, numerical data) Location 40 contains the duration of various system timing functions. Example: If you
desire the duration of the Dynamic Battery Test to be 30 minutes, program [3]-[0]-[

r

] in segment 1 of this location. The

[3]-[0] is the number of minutes, and the [

r

] stores the data and moves to the next segment of this location.

Technical Manuals Online! - http://www.tech-man.com

Summary of Contents for NetworX NX-8





















































Reviews:

No comments

Related manuals for NetworX NX-8

Satel SP-4006 Series Installation Manual preview
SP-4006 Series
Brand: Satel Pages: 8
Panasonic Firetracker FT1020G3 CIE Operation Manual preview
Firetracker FT1020G3 CIE
Brand: Panasonic Pages: 180
Tecnoalarm Tecnofire TFA2-596 Installation Manual preview
Tecnofire TFA2-596
Brand: Tecnoalarm Pages: 64
SIIG FireWire 3-Port CardBus Quick Installation Manual preview
FireWire 3-Port CardBus
Brand: SIIG Pages: 8
SIIG DP FireWire 800 PCI-32T Quick Installation Manual preview
DP FireWire 800 PCI-32T
Brand: SIIG Pages: 12

Brands by name

Popular brands

Load more brands