GE Consumer & Industrial PGCS1NFXSS Technical Service Manual Download | Manualshive

Page: 50 / 74

background image

– 50 –

5. Separate the mullion face from the refrigerator

cabinet.

6. Disconnect the mullion face wire harness and

ground wire.

Wire Harness

Ground

Wire

7. Remove the four 3/16-in. Allen-head shoulder

bolts (2 on each side) that attach the mullion to
the freezer walls.

8. Pull out the mullion from the recesses (1 on

each side) in the freezer walls.

9. Disconnect the mullion wire harness.

Wire

Harness

Freezer/Fresh Food Mullion Heater

The freezer/fresh food mullion heater is foamed in
place and is located behind the cabinet

fl

ange and

between the freezer and fresh food compartments.

Note:

If the Energy Saver light is on, then the

freezer/fresh food mullion heater is disabled.

The heater is not replaceable.

Note:

To test the operation of the mullion heater,

disconnect the humidity sensor. Within the next 20
minutes (duty cycle), the control will recognize the
open humidity sensor, the heater will then receive
voltage, and the mullion will get warm.

Freezer Double Drawer (DD) Mullion
Assembly

The freezer double drawer mullion assembly
consists of a mullion heater bonded to a mullion
face. The mullion face is attached to the mullion
with 4 Phillips-head screws. The mullion is inserted
in 2 recesses and attached to the freezer walls with
four 3/16-in. Allen-head shoulder bolts.

To remove the freezer double drawer mullion
assembly:

Unplug the refrigerator.

1.

Remove the freezer baskets. (See

2.

Freezer Basket

Removal

.)

Remove the upper and lower freezer drawer

3.

fronts. (See

Freezer Drawers

.)

Remove the 4 Phillips-head screws that attach

4.

the mullion face to the mullion.

«
...
48
49
50
51
52
...
»

Summary of Contents for PGCS1NFXSS











































































Reviews:

No comments

Related manuals for PGCS1NFXSS

Brand: Koncar Pages: 69

Brand: Changhong Electric Pages: 10

Brand: Avanti Pages: 32

Brand: Infiniton Pages: 22

Brand: U-Line Pages: 15

Brand: Magic Chef Pages: 14

Brand: Daewoo Pages: 15

Brand: Caple Pages: 15

Brand: MicroFridge Pages: 2

Brand: elvita Pages: 116

Brand: inventum Pages: 52

Brand: Freggia Pages: 32

Brand: Cylinda Pages: 116

Brand: Caple Pages: 17

Brand: U-Line Pages: 18

Brand: GE Pages: 20

Side by Side 26

Brand: GE Pages: 72

GSF25TGTBBB and

Brand: GE Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands