GE Consumer & Industrial PGCS1NFXSS Technical Service Manual Download

Page: 12 / 74

– 12 –

Settings

Use Settings to access Screen Appearances, Button Beep,
and Units Metric/English. Access by: Home> Options>
Settings.

Press

•

Screen Appearance

to access Color Options,

Brightness, and Screen Saver.
Press

•

Button Beep

to turn beep on or off.

Press

•

Units Metric/English

to change temperature

presentation.

Cooling System Off

Access by: Home> Options> Cooling System Off. Press
Enter to turn the cooling system off. To turn the cooling
system back on, press the touch screen and press the

button.

Activate By:

Pressing

ENTER

Note

Turning the

•

cooling system OFF

stops cooling in

both the freezer and refrigerator compartments, but
does not shut off electrical power to the refrigerator.

When the unit is turned back on, it will be set to the

•

standard settings and will take up to 24 hours to
stabilize.

Screen Appearance

Access by: Home> Options> Settings > Screen
Appearance.

Press

•

Color Options

to select the color theme of the

touch screen.
Press

•

Brightness

to adjust the brightness of the

touch screen.
Press

•

Screen Saver

to turn on or off the screen saver

display.

Summary of Contents for PGCS1NFXSS











































































Search results

Summary of Contents for PGCS1NFXSS

Reviews:

Related manuals for PGCS1NFXSS

Brands by name

Popular brands

GE Consumer & Industrial PGCS1NFXSS, Technical Service Manual

Search results

Summary of Contents for PGCS1NFXSS

Reviews:

Related manuals for PGCS1NFXSS

Brands by name

Popular brands