GE Consumer & Industrial PGCS1NFXSS Technical Service Manual Download

Page: 54 / 74

– 54 –

To remove the fl owmeter:

Caution:

It may be necessary to bend the process

tube in order to remove the water valve. If it is
necessary to bend the process tube, use extreme
caution.

Remove the 1/4-in. hex-head screw that holds

the water valve to the cabinet.

Lift and move the valve to the right to disengage

the tab at the top of the valve.

Note:

When replacing or repairing the water line

•

tubing, ensure the end of the tubing is cut
square and fully inserted into the water valve
and

owmeter connectors.

Do not discard mounting bracket. The mounting

•

bracket is not available as a replacement part.

Connectors are identical (part # WR02X10471).

•

Process Tube

Outlet Tube

Flowmeter

The

owmeter is located in the machine

compartment behind the water valve. The water
valve must be removed to access the

owmeter.

Lift and rotate the

owmeter bracket

counterclockwise to disengage the 2 tabs at the
top of the bracket.

Carefully pull out the bracket and

owmeter.

Mark and disconnect the inlet and outlet tubes

from the

owmeter connectors.

Disconnect the wire harness from the

owmeter.

Remove three 1/4-in. hex-head screws from the

mounting bracket.

Note:

The

owmeter is attached to a mounting

bracket that is held to the cabinet with a 1/4-in.
hex-head screw and 2 tabs. It may be necessary to
use a stubby nutdriver or 1/4-in. ratchet wrench and
socket.

Remove the 1/4-in. hex-head screw from the

owmeter bracket.

Outlet Tube

Flow Meter

Water Valve

Inlet Tube

Wire Harness

Connector (1 of 2)

Summary of Contents for PGCS1NFXSS











































































Search results

Summary of Contents for PGCS1NFXSS

Reviews:

Related manuals for PGCS1NFXSS

Brands by name

Popular brands

GE Consumer & Industrial PGCS1NFXSS, Technical Service Manual

Search results

Summary of Contents for PGCS1NFXSS

Reviews:

Related manuals for PGCS1NFXSS

Brands by name

Popular brands