32
232003110G (03)
NOTE
SmartGUARD™ is an optional fire detection alarm system developed by GCC. Contact your local GCC
authorized distributor for more detail to have this safety option installed onto your system.
1.5 Safety Measures
1.5.1 General Safety
• LASER RADIATION WARNING: Exposure to laser radiation may result in physical burns and
severe eye damage. Proper use and regular maintenance of this machine is important to the
safety of all people in the immediate area.
• Prior to operation, carefully read and familiarize yourself with the warning label located on both
your laser system and in this manual.
• Never leave the machine unattended during the laser cutting and engraving process. The laser
may ignite combustible material. A well-maintained fire extinguisher and operational smoke or
fire detector should be kept in the vicinity of the machine.
• Caution—Use of control or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
Resulting debris from laser cutting are very dangerous and may cause fire hazard.
DO NOT leave debris and scraps inside laser machine after job finished. Always keep machine
clean after job finished.
Enable the SmartAIR™ nozzle when engraving or cutting materia that may easily ignite, such
as acrylic, wood, or paper.
Always wear safety goggles when the laser system is in operation. Reflective materia such as
mirrors, enameled brass and anodized aluminum may partially-reflect some of the invisible laser
radiation. Severe eye damage may occur if proper safety goggles are not worn.
Connect the machine to a properly grounded power outlet. Ensure the voltage of the power
source is identical to the voltage of the machine.
Do not open the laser access panel when the machine is plugged in
Do not attempt to modify or disassemble the laser module.
Do not attempt to remove or modify any component of the machine’s laser interlock safety
system.
WARNING
・
Resulting debris from laser processing are very dangerous and may cause fire hazard
・
DO NOT leave debris and scraps inside laser machine after job finished. Must keep machine clean after job
finished.
・
Always remove the vector grid to clean any small pieces that have fallen through the grid.
Summary of Contents for LaserPro S400
