background image

14

 

NEOSERV 114

 

 

 gbo Medizintechnik AG 2004

 

Version 1.5

 

For hygienic reasons, the sponges must always be washed following termination of the treatment session 

(for this, see chapter 6.2.2)

 
 

 
 

5 Troubleshooting 

5.1 Error 

Messages 

The following failures will be indicated optically by 

NEOSERV 114

.  

 

• 

Overtemperature LED flashing 

 

1.  If overtemperature is very high (90 - 100 °C), the red LED will start flashing and the pump will be 

switched off immediately. 

2.  As soon as the pump has cooled down, the alarm lamp will go off automatically. Now the unit is 

again ready for operation. 

3.  If overtemperature occurs even though the unit has been operated only for a short time (less than one 

hour), at any rate contact your service representative to have the device checked. 

 

• 

Water level indicator flashing 

 

The water level within the water separator is too high. 

See chapter 3.4

 for draining the water separator. 

 
 
 

5.2 Other 

Troubles 

Trouble

 

Potential Cause

 

No or insufficient sucking action 

– 

Foreign particles have accumulated inside the suction 
electrode(s) 

– 

Suction electrodes draw in secondary air 

– 

Leakage in tubing (electrode lines) 

– 

Controls (front panel) in lowest position 

– 

Internal fault (Notify Technical Service!) 

Red LED

 

(overtemperature) 

flashing 

– 

Pump has run hot 

(see chapter 5.1)

 

– 

Check suction electrodes for potential foreign particles 
(clogging) 

– 

Replace suction electrodes if necessary 

– 

Internal fault (Notify Technical Service!) 

Green LED (POWER ON lamp) 
will not come on (or is not alight) 

– 

Unit not switched on; mains cable defective or not plugged in 

– 

Internal fault (Notify Technical Service!) 

– 

Power failure in the treatment room (main fuse) 

No stimulation effect generated 
(suction electrodes) 

– 

Electrotherapy unit switched off 

– 

Electrotherapy unit not connected to the 

NEOSERV 114

 

– 

Connecting cable, electrode line or electrode defective 

– 

Electrotherapy unit defective (Notify technical Service!) 

– 

Internal fault (Notify Technical Service!) 

– 

Stimulation current too low 

– 

Sponges dry 

 

 
In any other case of trouble or failure contact immediately gbo Medizintechnik AG

 

or one of the service 

agencies authorized by gbo Medizintechnik AG. 

Summary of Contents for NEOSERV 114

























Reviews: