background image

2

Location Requirements:

WARNING: 

This grill is Design Certified for use outdoors

   

only and is not intended for use on recreational

   

vehicles or boats.

The “Infrared Elite” is designed to be attached to the optional 

pedestal / cart or be permanently installed on a free-standing 

masonry or other suitable patio fixture.

Minimum clearance of a mobile grill to any adjacent

combustible construction can be found in Table A.

Table A.

If you are installing your grill as a brick-in or masonry supported

variation, it should be located so the ventilation louvers remain 

clear of all obstructions. The louvers are located in the front face 

of the grill and at the rear of the hood. Accumulation of debris in 

the louvers can cause the grill to overheat. There should be no 

combustible construction above the grill within 6 feet.

The installation of your grill must conform to local codes or, in 

the absence of local codes, with either the National Fuel Gas Code, 

ANSIZ223, 1 or CAN/CGA-B149.1, Natural Gas Installation Code or 

CAN/CGA-B149.2, Propane Installation Code.

 

Combustible  Non-Combustible

 

Construction 

Construction

Sides 

12” 

0”

Back 

12” 

0”

Summary of Contents for Infrared Elite I





















Reviews: