background image

36

Chapter 5: Setting Up the New Drive Automatically

www.gateway.com

Setting up the hard drive

The red 

Drivers

 CD, the 

Gateway System Restoration Kit

, or the 

Gateway System 

Restoration CD

 that originally came with your computer contains a program that 

will automatically set up an empty hard drive. The program will partition and 
format the drive, then install Windows for you. If you are using:

The red 

Drivers

 CD, go to “Using the red Drivers CD” on page 36.

The 

System Restoration Kit

, go to “Using the System Restoration Kit” on 

page 38.

The 

System Restoration CD

, go to “Using the System Restoration CD” on 

page 39.

Using the red Drivers CD

To set up a hard drive automatically using the red 

Drivers CD:

1

Insert the red 

Drivers

 into the CD or DVD drive.

2

Restart your computer.

3

Select 

2. Boot from CD-ROM

.

4

Select a language option.

5

Select 

1. Delete all files (Automated Fdisk/Format)

.

6

Select 

1. Continue deleting all files and restart

.

7

When prompted, press any key to continue.

8

Select 

2. Boot from CD-ROM

.

9

Select a language option.

10

Select 

2. Automated installation of Windows (XP or 2000)

.

Tips & Tricks

If you do not have your original system CDs, go to 

www.support.gateway.com

 to download any drivers you 

need.

Summary of Contents for DX4320

































































Reviews: