TYPE 1 Boltless Shelving
Assembly Instructions
FRAME ASSEMBLY
S T E P O N E
S T E P T W O
Place post flat on the ground so that Post Connector slots
are on the inside and the seam is on the outside. Post
Connector slots are adjustable every 12" (305mm).
Arrange Post Connectors at desired location, normally
evenly spaced, with one always at top and bottom of
post.
Starting from the bottom tap in one side of the Post
Connector and LOCK IMMEDIATELY. Then tap in
and lock the other side. The post will have to be
spread lightly as you work your way up the post. Use
a 1/4" or a 3/8" screwdriver or chainsaw wrench to
lock connectors. Assembly time is approximately 1 to
2 minutes per 84" (2134mm) frame.
POST CONNECTOR MUST BE LOCKED FOR SAFETY
LOAD CAPACITIES (IN LBS.)
Maximum evenly distributed static load per pair of connectors
SHELF LENGTH
36" 42" 48" 60" 66" 72" 96"
PB Frame Connectors
400
340
300
150
-
-
-
B Frame Connectors
with L Tie & O Shelf Support
700
1400
620
1100
550
900
400
530
-
-
-
-
-
-
WB Frame Connectors
with WT Combination Tie Bar & Shelf Support
1200
1800
1050
1640
950
1500
700
1200
575
1030
480
900
-
-
HD Frame Connectors
with WT Combination Tire Bar & Shelf Support
1650
2000
1550
1950
1400
1900
1000
1700
900
1600
800
1500
450
900
*
XHD Frame Connectors
with WT Combination Tie Bar & Shelf Support
-
-
-
-
-
2400
-
2400
-
2400
-
2400
-
1700
*
Connectors are designed for an overall Safety Factors of 1.66 to 1 which conforms to AISI Standards. Deflection is limited to 1/140 for spans.
*
Two WT Combination Tie Bar and Shelf Supports must be used.
E-Z-RECT MANUFACTURING LTD.
Head Office: North Vancouver, P: 604 929 5461 Eastern Sales: Mississauga, P: 905 564 0890 UK Sales: Oxon, P: 01993 779494
Email:
Web:
www.ezrect.ca
Email:
Web:
www.ezrect.ca
Email:
Web:
www.ezrshelving.com
E-Z-Rect Manufacturing Ltd. T1 Revision May 2019
BLACK PLASTIC TOP
OR BOTTOM CAP
Install top cap after assembly.
SHELF CLIP
4 required per shelf level
(2 right hand and 2 left hand).
Use with metal shelves.
PB FRAME CONNECTOR
Use particle board shelves, or use
PB 90
°
connectors for metal shelves.
B FRAME CONNECTOR
Use with metal or wood shelves.
WB FRAME CONNECTOR
Use with metal or wood shelves.
CONNECTOR LOCKING CLIP
Use to lock connectors for mezzanine,
catwalk & seismic applications.
XHD FRAME CONNECTOR
Use with metal or wood shelves.
HD FRAME CONNECTOR
Use with metal or wood shelves.
COMBINATION TIE BAR
Fits WB & HD frame connectors
for added strength.
Allow CTB hook to snap into
Connector slot with its own spring.
POST CONNECTOR
Use for making up end frames.
SHELF BAR
2 required per shelf level.
Use any frame connector
(except PBL 90
°
) or on shelf clips
SECTIONAL SHELF
Use with shelf bar. Frame connectors
& Combination tie bar required for
heavier loads and longer spans.
POLYPROPYLENE FLOOR PROTECTOR
Polypropylene levelling shim available.
ONLY FOUR BASIC COMPONENTS
1. Post 3. Frame Connector
2. Post Connector 4. Shelf (metal or particle board)
All upright posts are slotted 2" (51mm) centers
For maximum shelf adjustment.
FRAME
CONNECTOR
SHELF
POST
POST
CONNECTOR
HEIGHT
3' TO 20'
WIDTH
3' TO 8'
DEPTH
1' TO 4'
POST
POST
CONNECTOR
LOCK
FIRST
LOCK
THIRD
LOCK
FIFTH
LOCK
SIXTH
LOCK
FOURTH
LOCK
SECOND
SAFETY
TWIST LOCK
SCREWDRIVER OR
CHAINSAW WRENCH
POST SPLICE
•
Use for extending post.
•
Join two internal post splices together to form a cross.
Hammer into one post half way.
•
Place top post over post splices and tap down carefully until
posts meet.
•
Attach two external post splices on the outside of the joined
posts and secure them together with bolts and nuts.
TAB NOT LOCKED LOCKED TAB FULLY LOCKED
PLEASE FOLLOW ASSEMBLY INSTRUCTIONS. DO NOT USE SHELVES OR CONNECTORS WITH COMPONENTS OTHER THAN E-Z-RECT PRODUCTS.
