Gates Underwater Products EX1R Setup, Use And Care Manual Download Page 3

Page: 3 / 26

Gates Underwater Products, Inc

13685 Stowe Drive • Poway, CA • 92064 • 858.391.0052 • 800.875.1052 • Fax 858.391.0053

[email protected] • www.GatesHousings.com

01/13/10

Microphone information.

If you have the optional microphone installed, set the

camera as described in detail on page 21.

Slide the manual focus ring

to the forward position.

Set Zoom to ‘Servo’.

This switch is located at the base of the camera under the

lens.

Install

a memory card and charged battery.

Rotate the hand grip 1 stop
clockwise. Tighten the handstrap
fully and tuck the ‘tail’ into the
leather guide.

Remove the boom
microphone and holder.

Remove any caps, lenses or
filters from the camera lens.
Slide the focus ring into the
forward position.

Set the zoom switch to
‘Servo’.

Remove the
eyepiece from the
viewfinder.

Summary of Contents for EX1R



























Search results

Summary of Contents for EX1R

Reviews:

Related manuals for EX1R

Brands by name

Popular brands

Gates Underwater Products EX1R, Setup, Use And Care Manual

Search results

Summary of Contents for EX1R

Reviews:

Related manuals for EX1R

Brands by name

Popular brands